English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
إضاءة الغرف النظيفة والمعدات الكهربائية
صينية كابلات الفولاذ المقاوم للصدأ
A corrosion-resistant stainless cable-support system for wet, chemical-cleaning or hygienic cleanroom service routes.
- SUS304 or SUS316L
- Pickled and Passivated Finish
- Deburred Hygienic Edges
- Corrosion-Resistant Fittings
مقدمة المنتج
The stainless cable tray is formed from 304 or 316L sheet, wire or ladder components and then cleaned, pickled and passivated to restore a uniform protective surface. Smooth bends, stainless splice hardware and compatible supports prevent mixed-metal corrosion. Solid covers are available where the route is visible in the cleanroom, while ventilated or wire profiles can be used in service voids where heat dissipation is more important.
الخصائص الرئيسية
Pickling removes fabrication scale and passivation restores the protective surface film.
Deburred edges protect both cable jackets and cleaning gloves.
Stainless fasteners avoid dissimilar-metal staining at tray joints.
Matching covers and fittings maintain one material system through the route.
مخاوف المنتج للعملاء
Stainless tray performance depends on grade, fabrication finish and compatible joint hardware rather than material name alone.
Carbon-steel cut edges rust after repeated chemical cleaning.Stainless construction and post-fabrication passivation remove exposed ferrous coating breaks.
Mixed plated hardware produces rust streaks at joints.Matched stainless bolts, washers and supports maintain material compatibility.
Burrs cut cable jackets during installation.Rounded and mechanically deburred edges protect pulled conductors.
Open tray contents create a visible dust shelf.A fitted stainless cover closes exposed runs while remaining removable.
تطبيقات نموذجية
Pharmaceutical washdown areasClean utility plantsFood and biotechnology facilitiesCorrosive laboratory services
المعلمات الفنية
Typical configurable construction ranges for a stainless steel cable tray are listed below.
| المواد الأساسية | SUS304 or SUS316L sheet, wire or ladder tray with matching stainless covers, fittings and fasteners |
|---|---|
| سمك اللوحة | 50-150 mm tray side-wall or ladder depth |
| العرض الفعال | 100-900 mm usable tray width |
| الحد الأقصى الطول | Up to 3000 mm per straight section |
| الصلب يواجه سمك | 1.0-2.5 mm stainless tray and cover thickness |
| الكثافة الأساسية | Approximately 7900-8000 kg/m³ for austenitic stainless steel |
| الموصلية الحرارية | 14-16 W/(m·K) for SUS304/SUS316L material |
| إنهاء السطح | Pickled and passivated matte stainless, or fine-brushed sanitary finish |
| نوع المشترك | Bolted stainless splice plates with matched bends, support brackets and removable cover |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
SUS304 or SUS316L gradeSolid, perforated, wire or ladder profileOpen or covered constructionCustom support spacing and fittings
Planning a Stainless Steel Cable Tray specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
