English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
معدات تهوية وتكييف ومعالجة الهواء في الغرف النظيفة
وحدة معالجة الهواء المدمجة
A factory-assembled short-footprint air handler that integrates essential filtration, coil and fan functions for smaller controlled spaces.
- Short Equipment Footprint
- Factory-Assembled Package
- Integrated Controls
- Accessible Service Side
مقدمة المنتج
The compact air handling unit combines closely matched filters, coil and direct-drive fan in a monobloc or two-section casing. Component spacing is optimized to reduce overall length while maintaining coil drainage and filter removal. Integrated controls can manage fan speed, valve output, frost protection and filter alarms. The package suits smaller clean support rooms and retrofit locations where a full modular AHU would occupy excessive plant space.
الخصائص الرئيسية
Factory-installed controls simplify fan, coil and frost-protection integration.
Direct-drive fans eliminate belt clearance and reduce maintenance inside the compact casing.
Multiple duct orientations help the unit fit above, beside or behind existing services.
مخاوف المنتج للعملاء
Compact equipment must save space without compressing filters, drains and service points until maintenance becomes impractical.
A conventional modular AHU is longer than the available mechanical room.Close-coupled components and a direct-drive fan shorten the casing.
Filter removal collides with nearby pipework.The service side and pull direction are selected to match the actual clear zone.
Condensate is drawn off the coil because the fan is too close.A sized separation space and sloped drain pan preserve moisture control.
Field-mounted controls occupy additional wall and wiring space.A unit-mounted controller and sensors centralize the operating package.
تطبيقات نموذجية
Small cleanroom suitesLaboratory support roomsمناطق التفتيش على الأجهزة الطبيةControlled storage spacesRetrofit ventilation systems
المعلمات الفنية
Typical construction ranges for a compact insulated air handler are listed below.
| المواد الأساسية | Closed-cell polyurethane or mineral-wool insulation in compact double-skin casing |
|---|---|
| سمك اللوحة | 25–50 mm insulated panel |
| العرض الفعال | 600–1800 mm nominal casing width |
| الحد الأقصى الطول | Up to 4500 mm complete assembled length |
| الصلب يواجه سمك | 0.6–0.8 mm galvanized or coated sheet skins |
| الكثافة الأساسية | 38–42 kg/m³ polyurethane or 60–85 kg/m³ mineral wool |
| الموصلية الحرارية | 0.023–0.040 W/(m·K) depending on insulation |
| إنهاء السطح | Powder-coated galvanized exterior with smooth galvanized inner surfaces |
| نوع المشترك | Gasketed monobloc or two-section casing with removable service panels |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Horizontal, vertical or top-connected casingChilled-water or DX coolingEC fan and integrated controllerPlate or rotary heat-recovery section
Planning a Compact Air Handling Unit specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
