English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة الجدار والسقف للغرفة النظيفة
H-نوع لوحة غرفة نظيفة اتصال الشخصي
An extruded aluminum H-section that receives two opposing cleanroom panels and maintains a straight, protected joint along a modular wall or ceiling run.
- Opposed channels for two panel edges
- Straight in-plane modular connection
- Compatible with multiple panel thicknesses
- Sealable exposed joint boundaries
مقدمة المنتج
The H-Type Cleanroom Panel Connecting Profile joins two sandwich panels edge to edge in the same plane. Its opposed channels locate both panel ends, cover exposed core edges and establish a repeatable joint width. The aluminum section can be used in straight wall runs, ceiling infill and removable service bays where a defined mechanical connection is preferred over a tongue-and-groove-only joint.
الخصائص الرئيسية
The H-section conceals both cut edges and limits direct exposure of the panel core.
A continuous visible face creates a deliberate architectural joint.
Multiple channel sizes accommodate common cleanroom panel thicknesses.
Straight perimeter lands support controlled sealant application on both sides.
مخاوف المنتج للعملاء
An in-line panel joint must keep two large panels aligned while protecting their edges and maintaining a sealable interface.
Independent panel ends can step out of plane and create a visible ridge.Opposed channels hold both edges against one shared extruded connector.
Cut sandwich-panel cores remain exposed at butt joints.The H-shaped profile encloses both ends within dedicated receiving channels.
A freehand butt joint varies in width over the height of a wall.The fixed extrusion geometry maintains a consistent center joint from end to end.
Replacing one service panel can disturb the neighboring wall module.A defined connector profile separates the panel interfaces and supports modular removal strategies.
تطبيقات نموذجية
Straight modular cleanroom wall runsCeiling panel connectionsReplaceable service-bay infill panelsControlled-environment partition extensionsConnections between compatible panel modules
المعلمات الفنية
Channel dimensions are selected to suit the connected sandwich-panel thickness. Thermal values for an insulated panel do not describe this solid aluminum joining component.
| المواد الأساسية | 6063-T5 extruded aluminum H-section |
|---|---|
| سمك اللوحة | 50, 75, 80, 100 or 150 mm compatible variants |
| العرض الفعال | 50 mm typical visible joint face |
| الحد الأقصى الطول | 6000 mm |
| الصلب يواجه سمك | N/A — the connector is an aluminum extrusion |
| الكثافة الأساسية | N/A — no insulated core; aluminum alloy density is approximately 2700 kg/m³ |
| الموصلية الحرارية | N/A — no insulated core; aluminum alloy is approximately 200 W/(m·K) |
| إنهاء السطح | Electrostatic powder-coated or clear anodized aluminum |
| نوع المشترك | Twin opposed H-channels with sealant-ready panel interfaces |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
H-profile for 50 mm panelsH-profile for 75 or 80 mm panelsH-profile for 100 or 150 mm panelsAnodized or powder-coated exposed finish
Planning a H-Type Cleanroom Panel Connecting Profile specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
