English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
اكسسوارات تركيب الغرف النظيفة
لوحة غرفة نظيفة موصل
A concealed galvanized connector that aligns adjacent insulated cleanroom panel edges and transfers joint loads into their internal channels.
- Concealed Joint Hardware
- Positive Edge Alignment
- Galvanized Steel Strength
- Serviceable Mechanical Fixing
مقدمة المنتج
The cleanroom panel connector is a formed galvanized-steel component placed between compatible sandwich-panel edge channels. Its tongues, flanges or locating ribs engage both panel edges so the finished faces remain aligned while screws secure the connector to the internal reinforcement. Because the hardware is concealed by the closed joint, the exposed cleanroom surface can remain flush and ready for final sealing.
الخصائص الرئيسية
Galvanized steel provides practical stiffness and corrosion protection inside the concealed joint.
Countersunk or recessed fixing points keep fastener heads below the finished panel face.
Connector geometry can be matched to wall, ceiling or return-panel internal channels.
مخاوف المنتج للعملاء
Adjacent panels must stay flush during installation even when their light-gauge facings cannot carry alignment loads alone.
Panel faces step out of alignment while installers tighten the joint.Locating tongues engage both internal channels and establish a common joint plane.
Surface fasteners create visible recesses that are difficult to finish hygienically.The connector and its fixings remain concealed within the panel-edge cavity.
Thin sheet facings deform when joint loads are concentrated at one screw.A formed connector spreads load along the internal edge reinforcement.
Generic brackets do not fit the panel manufacturer's tongue-and-groove geometry.Connector width, rib position and hole pattern are matched to the selected panel section.
تطبيقات نموذجية
Cleanroom wall-panel jointsWalkable ceiling panel connectionsPartition return panelsDoor-frame infill interfacesModular enclosure assembly
المعلمات الفنية
Typical construction ranges for a formed galvanized cleanroom sandwich-panel connector are shown below.
| المواد الأساسية | Formed galvanized carbon-steel connector with stamped ribs and fixing holes |
|---|---|
| سمك اللوحة | 50-150 mm compatible sandwich-panel thickness |
| العرض الفعال | 40-200 mm connector engagement width |
| الحد الأقصى الطول | Up to 3000 mm continuous spline or 500 mm discrete connector length |
| الصلب يواجه سمك | 1.00-2.50 mm galvanized connector sheet thickness |
| الكثافة الأساسية | Approximately 7850 kg/m³ for galvanized carbon steel |
| الموصلية الحرارية | Approximately 45-60 W/(m·K) for carbon-steel connector parts |
| إنهاء السطح | Silver zinc-coated formed steel concealed within white coated panel edges |
| نوع المشترك | Concealed spline, tongue, bridging plate or channel engagement with mechanical fixing |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Continuous spline or discrete plateWall or ceiling profilePre-punched fixing holesStainless-steel construction
Planning a Cleanroom Panel Connector specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
