English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
معدات تهوية وتكييف ومعالجة الهواء في الغرف النظيفة
وحدة الهواء الماكياج
A dedicated outdoor-air unit that replaces exhausted process air and maintains the intended cleanroom pressure relationship.
- Exhaust Air Replacement
- Pressure Cascade Support
- Tempered Outdoor Supply
- Airflow Tracking Control
مقدمة المنتج
The makeup air unit delivers conditioned outside air in proportion to fume-hood, process, canopy or room exhaust. Unlike a general fresh-air unit, its primary control duty is mass-balance: supply airflow must respond predictably as exhaust devices start, stop or modulate. Filters, coils and optional humidity treatment bring the outdoor air to a condition that the room or recirculation system can accept without upsetting temperature and moisture control. A low-leakage casing and fast fan response help prevent door forces and unwanted infiltration.
الخصائص الرئيسية
Tempering coils prevent replacement air from imposing abrupt heating, cooling or moisture loads on the cleanroom.
Fast variable-speed fan control supports stable room pressure during process exhaust transitions.
Separate intake filtration prevents outdoor particles from entering through uncontrolled building leakage paths.
مخاوف المنتج للعملاء
A facility can have sufficient cooling capacity yet still lose pressure control when exhaust and replacement air do not change together.
Starting a process exhaust fan pulls adjacent cleanrooms below their pressure setpoint.The makeup fan follows the combined exhaust airflow signal with a configured offset for pressure cascade.
Untempered winter replacement air causes cold drafts and local condensation.Preheat and final heating stages deliver supply air at a controlled temperature.
Outdoor humidity overwhelms the room AHU during high exhaust operation.Cooling and dehumidification are sized for the full makeup-air latent load.
Unfiltered infiltration enters around doors when replacement air is insufficient.Measured makeup volume enters through staged filters and a defined supply path.
تطبيقات نموذجية
Pharmaceutical process exhaust replacementLaboratory fume-hood makeup airClean manufacturing canopy exhaustChemical handling roomsHospital isolation support areas
المعلمات الفنية
Representative makeup-air unit casing and connection ranges are provided below.
| المواد الأساسية | Closed-cell polyurethane or mineral-wool insulation within double-wall casing |
|---|---|
| سمك اللوحة | 50–60 mm insulated panel |
| العرض الفعال | 800–3000 mm nominal casing width |
| الحد الأقصى الطول | Up to 9000 mm with staged filtration and thermal treatment |
| الصلب يواجه سمك | 0.6–1.0 mm sheet steel casing skins |
| الكثافة الأساسية | 40–43 kg/m³ polyurethane or 80–96 kg/m³ mineral wool |
| الموصلية الحرارية | 0.022–0.040 W/(m·K) according to insulation selection |
| إنهاء السطح | Powder-coated galvanized exterior with galvanized or stainless wet-section interior |
| نوع المشترك | Thermal-break frame and gasketed block joints with flexible supply-duct connector |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Exhaust-airflow or room-pressure trackingGas, steam, hot-water or electric heatingChilled-water, DX or desiccant dehumidificationOutdoor roof, floor or plant-room arrangement
Planning a Makeup Air Unit specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
