English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
اكسسوارات تركيب الغرف النظيفة
لوحة غرفة نظيفة المشبك
A reusable stainless-steel bridge clamp that holds adjacent sandwich-panel edges in alignment while their joint is fixed and sealed.
- Reusable Installation Tool
- Opposed Edge Jaws
- Threaded Force Control
- No Permanent Face Fixing
مقدمة المنتج
The cleanroom panel clamp is an external installation tool with opposed formed jaws and a threaded adjuster. The jaws bear on protected panel edges while the screw draws adjacent sandwich panels into a stable working position. Installers can therefore check face alignment, close the joint and complete concealed fixing before removing the clamp, without leaving the tool as part of the finished enclosure.
الخصائص الرئيسية
A coarse threaded adjuster provides progressive, controllable closing force during alignment.
Stainless construction tolerates repeated handling and can be cleaned between installation areas.
Replaceable contact pads or protected jaw faces can reduce marking on coated steel skins.
مخاوف المنتج للعملاء
Lightweight insulated panels can move or develop a face step before concealed joint hardware and sealant have secured the assembly.
Two panel faces drift out of plane while the concealed fixing is tightened.The bridge clamp holds both edges against a common jaw position during fastening.
Uncontrolled leverage can dent thin coated-steel facings.Threaded adjustment applies force gradually, with jaw pads selected for the facing finish.
Temporary screws leave holes that require hygienic repair.External jaws grip removable edge locations without adding permanent face penetrations.
Different panel thicknesses make a fixed-gap tool impractical.Jaw reach, bridge width and screw travel can be matched to the installed panel system.
تطبيقات نموذجية
Cleanroom wall-panel erectionCeiling panel edge alignmentModular enclosure assemblyJoint sealing preparationDoor and window infill installation
المعلمات الفنية
Typical construction ranges for a reusable stainless cleanroom sandwich-panel alignment clamp are listed below.
| المواد الأساسية | 304 stainless-steel bridge, opposed formed jaws and threaded adjuster |
|---|---|
| سمك اللوحة | 50-150 mm compatible sandwich-panel thickness |
| العرض الفعال | 60-240 mm adjustable jaw span |
| الحد الأقصى الطول | Up to 500 mm overall clamp bridge length |
| الصلب يواجه سمك | 2.00-6.00 mm structural clamp component thickness |
| الكثافة الأساسية | Approximately 7900-8000 kg/m³ for stainless-steel components |
| الموصلية الحرارية | Approximately 14-17 W/(m·K) for austenitic stainless steel |
| إنهاء السطح | Brushed or bead-blasted stainless steel with optional non-marking jaw pads |
| نوع المشترك | Removable opposed-jaw bridge clamp with threaded mechanical adjustment |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
304 or 316 stainless steelSoft polymer jaw padsHex-bolt or hand-knob adjustmentCustom jaw reach and span
Planning a Cleanroom Panel Clamp specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
