English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
ملابس الغرف النظيفة، PPE والمواد الاستهلاكية
مئزر غرفة نظيفة
A lightweight low-lint cleanroom apron providing targeted front-torso and leg coverage with adjustable ties.
- Shin-length low-lint front coverage
- Adjustable neck and waist ties
- Disposable or reusable material options
مقدمة المنتج
The Cleanroom Apron is a simple over-garment for tasks that need additional front-surface coverage without a full garment change. Its one-piece bib, smooth front panel, adjustable neck loop and long waist ties minimize hardware and allow quick donning. White flash-spun polyethylene, film-coated material or reusable polyester can be selected to suit handling and processing needs.
الخصائص الرئيسية
Shin-length format extends coverage below the workbench edge
Adjustable neck loop accommodates different operator heights
Long waist ties secure the apron without exposed metal hardware
Smooth pocket-free surface simplifies controlled handling
مخاوف المنتج للعملاء
An apron provides partial rather than full-body coverage. Material selection, gown overlap and disposal or laundering procedures must therefore match the actual task and the base garment worn underneath.
A short apron may leave the lower torso or upper legs exposed.Select shin-length coverage and suitable width for the operator and work posture.
Fixed neck dimensions can place the bib too high or low.Use an adjustable neck loop and long rear waist ties for controlled positioning.
Pockets and bulky fasteners can trap residues and particles.Specify a smooth pocket-free front with minimal seam count and no exposed hardware.
The apron material may not match the intended splash or ESD requirement.Choose the exact nonwoven, film-coated or conductive polyester construction based on task data.
تطبيقات نموذجية
Used for controlled dispensing, clean packing, laboratory preparation, equipment wipe-down, visitor protection and other front-facing tasks where local gowning rules permit partial over-garment coverage.
المعلمات الفنية
These configurable dimensions describe a cleanroom apron, not a full protective garment. Final material and coverage must be selected after reviewing the base gowning system and process exposure.
| المواد الأساسية | Flash-spun polyethylene, low-lint film or continuous-filament polyester |
|---|---|
| سمك اللوحة | 0.14–0.35 mm |
| العرض الفعال | 650–900 mm |
| الحد الأقصى الطول | 1250 mm |
| الصلب يواجه سمك | 0 mm; no steel facing used |
| الكثافة الأساسية | 45–125 kg/m³ apparent material bulk density |
| الموصلية الحرارية | 0.035–0.060 W/(m·K), material dependent |
| إنهاء السطح | Smooth low-lint white or light-blue surface without pockets |
| نوع المشترك | One-piece front panel with sewn or bonded neck and waist ties |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
White disposable nonwoven or reusable polyesterSleeveless bib or long-sleeve apronAdjustable neck loop or snap-adjusted neck strapRear ties or low-profile buckle systemConductive-grid polyester optionIndividual or bulk clean packaging
Planning a Cleanroom Apron specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
