English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة توزيع الهواء في الغرف النظيفة
Bubble-Tight عزل المثبط
A heavy rectangular isolation damper whose solid butterfly blade compresses a mechanically retained perimeter seal under high closing torque.
- Solid Butterfly Isolation Blade
- Mechanically Retained Perimeter Seal
- Double-Gland Axle Packing
- Heavy Flanged Channel Frame
مقدمة المنتج
The bubble-tight isolation damper uses one rigid rectangular butterfly blade inside a heavy flanged channel frame. When the actuator rotates the blade to closed, a continuous silicone seal is compressed against the seat around the complete perimeter. The drive axle passes through a double-gland stuffing box, and outboard bearings keep the blade aligned without placing the bearing races in the air path. Stainless-steel construction and compatible coatings allow the assembly to serve isolation, wash-down and decontamination boundaries.
الخصائص الرئيسية
The perimeter seal is mechanically fastened to the blade so it can be inspected and replaced without welding.
Double-gland axle packing restricts leakage around the rotating shaft where it exits the pressure boundary.
External relubricable bearings carry radial load while remaining accessible outside contaminated airflow.
مخاوف المنتج للعملاء
Bubble-tight service demands uniform perimeter compression, controlled shaft leakage and a frame stiff enough to remain square under differential pressure.
A multiblade damper leaves several blade-to-blade leakage paths at a critical boundary.One solid butterfly blade closes against a continuous seat with no intermediate blade joints.
The axle penetration leaks even though the blade perimeter is fully seated.A double-gland stuffing box seals around the rotating shaft outside the primary blade seal.
High differential pressure deflects a light frame and unloads part of the gasket.Heavy channel construction and a reinforced backing plate maintain seat geometry under closing load.
A damaged perimeter seal requires replacement of the complete blade assembly.Mechanical seal retainers allow the gasket to be removed and renewed as a service component.
تطبيقات نموذجية
Biocontainment duct isolationPharmaceutical decontamination zonesHigh-integrity laboratory exhaustFilter housing isolation boundariesContaminated process-air shutdown
المعلمات الفنية
Representative construction data for a heavy-duty rectangular bubble-tight isolation damper are shown below.
| المواد الأساسية | Solid 304 or 316 stainless-steel butterfly blade with continuous silicone perimeter seal |
|---|---|
| سمك اللوحة | 2.7 mm solid rectangular blade plate |
| العرض الفعال | 254–1130 mm nominal clear opening width |
| الحد الأقصى الطول | Up to 1321 mm nominal frame height |
| الصلب يواجه سمك | 2.7 mm stainless or coated-steel flanged channel frame |
| الكثافة الأساسية | Approximately 8000 kg/m³ for austenitic stainless-steel blade construction |
| الموصلية الحرارية | Approximately 14–16 W/(m·K) for 304 or 316 stainless steel |
| إنهاء السطح | Mill-finish stainless steel or industrial epoxy coating with silicone blade seal |
| نوع المشترك | Flanged channel frame with solid butterfly blade, bolted seal retainer and double-gland axle stuffing box |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
304 or 316 stainless-steel constructionElectric or pneumatic high-torque actuatorOpen-close position switchesIndustrial epoxy or polyester coating
Planning a Bubble-Tight Isolation Damper specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
