Three-quarter view of a heavy-duty bubble-tight isolation damper

Системы распределения воздуха в чистых помещениях

Пузырькопрочные изоляционные амортизаторы

A heavy rectangular isolation damper whose solid butterfly blade compresses a mechanically retained perimeter seal under high closing torque.

Solid Butterfly Isolation Blade
Mechanically Retained Perimeter Seal
Double-Gland Axle Packing
Heavy Flanged Channel Frame

Запрос котировки Просмотреть продукты

Введение продукции

The bubble-tight isolation damper uses one rigid rectangular butterfly blade inside a heavy flanged channel frame. When the actuator rotates the blade to closed, a continuous silicone seal is compressed against the seat around the complete perimeter. The drive axle passes through a double-gland stuffing box, and outboard bearings keep the blade aligned without placing the bearing races in the air path. Stainless-steel construction and compatible coatings allow the assembly to serve isolation, wash-down and decontamination boundaries.

Основные характеристики

A single rigid blade provides an uninterrupted sealing face without intermediate multiblade joints.

The perimeter seal is mechanically fastened to the blade so it can be inspected and replaced without welding.

Double-gland axle packing restricts leakage around the rotating shaft where it exits the pressure boundary.

External relubricable bearings carry radial load while remaining accessible outside contaminated airflow.

Обеспокоенность клиентов продуктами

Bubble-tight service demands uniform perimeter compression, controlled shaft leakage and a frame stiff enough to remain square under differential pressure.

A multiblade damper leaves several blade-to-blade leakage paths at a critical boundary.One solid butterfly blade closes against a continuous seat with no intermediate blade joints.

The axle penetration leaks even though the blade perimeter is fully seated.A double-gland stuffing box seals around the rotating shaft outside the primary blade seal.

High differential pressure deflects a light frame and unloads part of the gasket.Heavy channel construction and a reinforced backing plate maintain seat geometry under closing load.

A damaged perimeter seal requires replacement of the complete blade assembly.Mechanical seal retainers allow the gasket to be removed and renewed as a service component.

Типичные приложения

Biocontainment duct isolationPharmaceutical decontamination zonesHigh-integrity laboratory exhaustFilter housing isolation boundariesContaminated process-air shutdown

Технические параметры

Representative construction data for a heavy-duty rectangular bubble-tight isolation damper are shown below.

Основной материал	Solid 304 or 316 stainless-steel butterfly blade with continuous silicone perimeter seal
Толщина панели	2.7 mm solid rectangular blade plate
эффективная ширина	254–1130 mm nominal clear opening width
Максимальная длина	Up to 1321 mm nominal frame height
Толщина линий стали	2.7 mm stainless or coated-steel flanged channel frame
Плотность ядра	Approximately 8000 kg/m³ for austenitic stainless-steel blade construction
Теплопроводимость	Approximately 14–16 W/(m·K) for 304 or 316 stainless steel
Поверхностная отделка	Mill-finish stainless steel or industrial epoxy coating with silicone blade seal
Объединенный тип	Flanged channel frame with solid butterfly blade, bolted seal retainer and double-gland axle stuffing box
Customization	Доступно в зависимости от предполагаемого применения и операционной среды.

Доступные варианты

304 or 316 stainless-steel constructionElectric or pneumatic high-torque actuatorOpen-close position switchesIndustrial epoxy or polyester coating

Planning a Bubble-Tight Isolation Damper specification?

Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.

Поговорите с нашей командой