English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
مرشحات الهواء والترشيح الكيميائي
Aمرشح جيب الكربون المنشط
A multi-pocket filter combining particulate media with a distributed activated-carbon layer to remove fine dust and light-duty gaseous contaminants in one HVAC stage.
- Particle and Gas Filtration
- Conical Pocket Geometry
- Distributed Carbon Layer
- Large Media Surface
مقدمة المنتج
The activated carbon pocket filter combines an upstream particulate layer, a bonded activated-carbon layer and a stabilizing downstream support within multiple tapered pockets. The long pockets provide a much greater media area than a flat panel and distribute both particle loading and carbon adsorption over the airflow. Stitched or ultrasonically welded spacers keep the pockets separated, while a steel or molded-polymer header fits standard bag-filter housings. It is intended for indoor-air-quality duty where moderate odors and particulates must be addressed without installing two separate filter stages.
الخصائص الرئيسية
Tapered pockets remain separated at design flow and use the available housing depth efficiently.
The distributed carbon layer exposes adsorbent across a broad area instead of concentrating it near the header.
A rigid header provides a familiar replacement interface for standard front- or side-access bag-filter systems.
مخاوف المنتج للعملاء
Separate particle and molecular stages consume valuable air-handler length, yet a thin carbon panel may not provide enough active area for the required airflow.
The air handler lacks space for a particle filter followed by a separate carbon cassette.Composite pocket media combines both functions within one standard bag-filter stage.
Flat carbon media has too little exposed area at the system airflow.Multiple deep pockets increase the available carbon-coated surface behind the same face opening.
Bag pockets touch and block one another at reduced airflow.Tapered geometry and internal spacing retain open channels through the filter bank.
Particulate loading covers the carbon before its adsorption capacity is used.A dedicated upstream particle layer protects the distributed carbon surface from coarse dust.
تطبيقات نموذجية
Commercial building supply airHospital general ventilationAirport and transport facilitiesLaboratory support-area HVACCleanroom prefiltration with odor control
المعلمات الفنية
Representative construction ranges for a combination activated-carbon pocket filter are shown below.
| المواد الأساسية | Synthetic or glass-fibre particulate medium laminated with bonded activated-carbon media |
|---|---|
| سمك اللوحة | 360–640 mm pocket depth |
| العرض الفعال | 287–592 mm nominal header width |
| الحد الأقصى الطول | Up to 640 mm pocket length |
| الصلب يواجه سمك | 0.6–0.9 mm painted or galvanized-steel header frame when specified |
| الكثافة الأساسية | Approximately 80–160 kg/m³ equivalent composite-media density including bonded carbon |
| الموصلية الحرارية | Approximately 0.040–0.080 W/(m·K) for the dry composite pocket medium |
| إنهاء السطح | Painted steel or molded polymer header with dark carbon-loaded pocket media |
| نوع المشترك | Header-frame gasket or clamp-in pocket-filter connection |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Five to ten pocket configurationsSteel or incinerable polymer headerParticulate efficiency selected for the HVAC stageBroad-spectrum or impregnated carbon layer
Planning a Activated Carbon Pocket Filter specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
