English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Воздушные фильтры и химическая фильтрация
Карманный фильтр активированного угля
A multi-pocket filter combining particulate media with a distributed activated-carbon layer to remove fine dust and light-duty gaseous contaminants in one HVAC stage.
- Particle and Gas Filtration
- Conical Pocket Geometry
- Distributed Carbon Layer
- Large Media Surface
Введение продукции
The activated carbon pocket filter combines an upstream particulate layer, a bonded activated-carbon layer and a stabilizing downstream support within multiple tapered pockets. The long pockets provide a much greater media area than a flat panel and distribute both particle loading and carbon adsorption over the airflow. Stitched or ultrasonically welded spacers keep the pockets separated, while a steel or molded-polymer header fits standard bag-filter housings. It is intended for indoor-air-quality duty where moderate odors and particulates must be addressed without installing two separate filter stages.
Основные характеристики
Tapered pockets remain separated at design flow and use the available housing depth efficiently.
The distributed carbon layer exposes adsorbent across a broad area instead of concentrating it near the header.
A rigid header provides a familiar replacement interface for standard front- or side-access bag-filter systems.
Обеспокоенность клиентов продуктами
Separate particle and molecular stages consume valuable air-handler length, yet a thin carbon panel may not provide enough active area for the required airflow.
The air handler lacks space for a particle filter followed by a separate carbon cassette.Composite pocket media combines both functions within one standard bag-filter stage.
Flat carbon media has too little exposed area at the system airflow.Multiple deep pockets increase the available carbon-coated surface behind the same face opening.
Bag pockets touch and block one another at reduced airflow.Tapered geometry and internal spacing retain open channels through the filter bank.
Particulate loading covers the carbon before its adsorption capacity is used.A dedicated upstream particle layer protects the distributed carbon surface from coarse dust.
Типичные приложения
Commercial building supply airHospital general ventilationAirport and transport facilitiesLaboratory support-area HVACCleanroom prefiltration with odor control
Технические параметры
Representative construction ranges for a combination activated-carbon pocket filter are shown below.
| Основной материал | Synthetic or glass-fibre particulate medium laminated with bonded activated-carbon media |
|---|---|
| Толщина панели | 360–640 mm pocket depth |
| эффективная ширина | 287–592 mm nominal header width |
| Максимальная длина | Up to 640 mm pocket length |
| Толщина линий стали | 0.6–0.9 mm painted or galvanized-steel header frame when specified |
| Плотность ядра | Approximately 80–160 kg/m³ equivalent composite-media density including bonded carbon |
| Теплопроводимость | Approximately 0.040–0.080 W/(m·K) for the dry composite pocket medium |
| Поверхностная отделка | Painted steel or molded polymer header with dark carbon-loaded pocket media |
| Объединенный тип | Header-frame gasket or clamp-in pocket-filter connection |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Five to ten pocket configurationsSteel or incinerable polymer headerParticulate efficiency selected for the HVAC stageBroad-spectrum or impregnated carbon layer
Planning a Activated Carbon Pocket Filter specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
