English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Системы полы для чистых комнат
Гигиенические чистые помещения виниловый лист пол
A low-emission homogeneous vinyl sheet developed for controlled environments where particle release, decontamination and sealed floor-to-wall transitions are primary concerns.
- Low-Particle Surface
- Heat-Welded Hygienic Seams
- Decontamination-Ready Finish
- Integral Coved Perimeter
Введение продукции
Hygienic cleanroom vinyl sheet flooring uses a dense, non-directional homogeneous PVC body with a smooth factory treatment designed to release soils without a separate wax layer. Wide rolls are fully adhered, routed and hot welded to create a continuous floor field. At room boundaries the same sheet can be formed over a cove former and terminated at the wall system, removing the sharp internal corner found at a conventional skirting joint. The cleanroom formulation prioritizes low particle emission, low outgassing and resistance to common chemical and vapor-phase decontamination routines.
Основные характеристики
Low-emission formulation is suited to controlled environments with strict airborne contamination management.
Hot-welded seams and coved perimeters create accessible transitions for validated cleaning procedures.
The surface is selected for resistance to common disinfectants and hydrogen-peroxide decontamination cycles.
Обеспокоенность клиентов продуктами
Cleanroom sheet flooring must control emissions and particles while remaining compatible with intensive disinfection and sealed room detailing.
Embossed or porous flooring retains residues after routine decontamination.A dense, smooth homogeneous surface provides fewer micro-textured retention points.
The floor-to-wall corner is difficult to wipe and inspect.Site-formed coving carries the sheet smoothly up the perimeter before it meets the wall finish.
Sheet seams open after repeated trolley movement and wet cleaning.Correct routing and compatible hot-welding rod fuse adjacent edges into a closed joint.
Vaporized disinfection agents discolor or soften general-purpose vinyl.The cleanroom formulation and seam components are selected for the planned chemical and decontamination cycle.
Типичные приложения
Pharmaceutical cleanroomsBiotechnology laboratoriesMedical-device assembly roomsSterile compounding support areasControlled research suites
Технические параметры
Representative dimensions and material data for homogeneous cleanroom vinyl sheet flooring are provided below.
| Основной материал | Type I homogeneous compact PVC with low-emission plasticizer, mineral filler and color pigments |
|---|---|
| Толщина панели | 2.0 mm full-thickness homogeneous construction |
| эффективная ширина | 2000 mm standard cleanroom sheet width |
| Максимальная длина | До 20000 мм стандартная длина вала |
| Толщина линий стали | 0 mm; the cleanroom vinyl sheet has no steel facing |
| Плотность ядра | Approximately 1300–1320 kg/m³ based on common 2.0 mm cleanroom sheet weights |
| Теплопроводимость | Approximately 0.25 W/(m·K) for the homogeneous vinyl body |
| Поверхностная отделка | Smooth non-directional matte finish with factory cross-linked maintenance treatment |
| Объединенный тип | Fully adhered and hot-welded sheet seams with site-formed coved wall transitions |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Cleanroom neutral and wayfinding colorsMatching hot-welding rodCove former, cap strip and wall transition profilesConductive or standard adhesive system to suit room requirements
Planning a Hygienic Cleanroom Vinyl Sheet Flooring specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
