English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
معدات تهوية وتكييف ومعالجة الهواء في الغرف النظيفة
وحدة التعامل مع الهواء العمودي
A stacked upflow or downflow air handler that reduces plant-room footprint while retaining full filter, coil and fan functionality.
- Small Floor Footprint
- Upflow or Downflow Layout
- Stacked Service Sections
- Rigid Vertical Frame
مقدمة المنتج
The vertical air handling unit stacks treatment components to use room height instead of long floor area. Air may enter low and discharge upward, or follow a downflow path to a raised floor or low duct. Filters, coils and fan sections are separated by accessible service zones, and the frame is reinforced for the vertical component load. Drain and trap geometry are arranged for the selected casing pressure, while lifting points and removable panels support installation in compact plant rooms.
الخصائص الرئيسية
Upflow and downflow discharge options align with high-level or underfloor duct systems.
Reinforced base and frame transfer fan, coil and filter loads through the vertical casing.
Dedicated access doors keep filter and wet-section service points reachable from one side.
مخاوف المنتج للعملاء
Stacking components saves floor space only if service access, drainage and structural loads are addressed in the vertical arrangement.
A horizontal unit blocks the only service aisle in a small plant room.Vertical stacking shortens the footprint while preserving treatment functions.
The discharge duct must turn sharply and adds unnecessary pressure loss.Upflow or downflow discharge connects directly to the building riser or floor plenum.
Upper filters are difficult to lift and remove safely.Filter stages are positioned at practical service height with slide-out tracks.
Condensate trap height is insufficient under negative casing pressure.The base frame provides clearance for a trap sized to the actual section pressure.
تطبيقات نموذجية
Compact cleanroom plant roomsHospital mechanical closetsLaboratory retrofit shaftsVertical supply risersUnderfloor clean-air systems
المعلمات الفنية
Typical casing values for an insulated vertical air handling unit are listed below.
| المواد الأساسية | Polyurethane or mineral-wool insulation in reinforced double-skin panels |
|---|---|
| سمك اللوحة | 40–60 mm insulated panel |
| العرض الفعال | 800–2400 mm nominal casing width |
| الحد الأقصى الطول | Up to 3500 mm horizontal base length for stacked configuration |
| الصلب يواجه سمك | 0.6–1.0 mm casing skins with reinforced base members |
| الكثافة الأساسية | 41–45 kg/m³ polyurethane or 84–100 kg/m³ mineral wool |
| الموصلية الحرارية | 0.022–0.040 W/(m·K) according to panel core |
| إنهاء السطح | Powder-coated galvanized exterior with galvanized or stainless inner lining |
| نوع المشترك | Compression-gasketed stacked panels on bolted structural base and vertical frame |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Upflow, downflow or side dischargeChilled-water, hot-water or DX coilsEC plug fan or fan arrayBottom or side return-air connection
Planning a Vertical Air Handling Unit specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
