English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
إضاءة الغرف النظيفة والمعدات الكهربائية
UV مصباح الموقت المراقب
A dedicated wall controller that sequences delayed start, timed UV-C operation, warnings and safety interlock inputs from one sealed panel.
- Keyed Enable Control
- Adjustable Cycle Timer
- Delayed Start Warning
- Door and Sensor Inputs
مقدمة المنتج
The UV-C controller separates germicidal operation from ordinary room-light switching. Its cleanable front panel carries a key switch, timer display, start/stop controls and status indicators. Inside the enclosure, a contactor or relay output switches the UV-C load while low-voltage terminals accept door contacts, occupancy sensors, warning beacons and remote emergency-stop devices.
الخصائص الرئيسية
The programmable delay provides a defined exit interval before lamp energization.
A digital display shows remaining treatment time and operating state.
Dedicated safety inputs interrupt the output when a monitored door opens or occupancy is detected.
Separate relay terminals operate external beacons and audible warnings.
مخاوف المنتج للعملاء
A basic timer alone cannot manage warning, authorization and interruption functions required around an unattended UV-C cycle.
Anyone can start a germicidal circuit from a normal wall switch.A key-controlled enable stage restricts initiation to designated operators.
Personnel have no time to leave after pressing start.An adjustable countdown drives warnings before the power relay closes.
Opening a door does not stop an independent timer output.Hardwired safety inputs drop the UV-C contactor immediately on an interlock event.
The operator cannot see whether a cycle ended or was interrupted.Distinct display states report standby, delay, active, complete and fault conditions.
تطبيقات نموذجية
Fixed UV-C room systemsPass-box germicidal circuitsDuct irradiation controlsLaboratory treatment rooms
المعلمات الفنية
Typical configurable construction ranges for a UV-C lamp safety timer controller are listed below.
| المواد الأساسية | Powder-coated steel or stainless enclosure with programmable timer, contactor, control relays and membrane interface |
|---|---|
| سمك اللوحة | 90-180 mm wall enclosure depth |
| العرض الفعال | 180-400 mm front-panel width |
| الحد الأقصى الطول | Up to 500 mm overall enclosure height |
| الصلب يواجه سمك | 1.0-1.5 mm formed steel or stainless enclosure panels |
| الكثافة الأساسية | Approximately 7900-8000 kg/m³ for a stainless enclosure version |
| الموصلية الحرارية | 14-16 W / (m·K) للعلبة الفولاذية |
| إنهاء السطح | White powder coat or fine-brushed stainless front with black display and colored status indicators |
| نوع المشترك | Gasketed enclosure door with sealed membrane controls and separated power and low-voltage terminal blocks |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Wall flush or surface enclosureLocal or networked timerDoor, motion and emergency-stop inputsExternal beacon and buzzer outputs
Planning a UV Lamp Timer Controller specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
