English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة توزيع الهواء في الغرف النظيفة
PIR قناة الهواء معزولة مسبقًا
A lightweight rigid duct fabricated from closed-cell PIR panels with aluminum foil facings that combine the air barrier and thermal insulation in one assembly.
- Closed-Cell PIR Core
- Integrated Thermal Insulation
- Aluminum Foil Facings
- Lightweight Panel Assembly
مقدمة المنتج
PIR pre-insulated ductwork is cut and folded from rigid closed-cell panels faced on both sides with aluminum foil. The finished duct eliminates the separate sheet-metal shell and external insulation layer used in conventional systems, reducing installed weight and limiting thermal bridges. Male-female panel edges, aluminum profiles, vapor-tight foil tape and compatible sealant form the longitudinal and transverse joints. The smooth foil interior suits dry conditioned supply and return air where the panel is protected from impact and the selected facing is compatible with cleaning practices.
الخصائص الرئيسية
Continuous foil facings create clean internal and external surfaces and support vapor control.
The combined duct-and-insulation panel reduces suspended load and installation operations.
Factory-routed grooves and aluminum closure profiles produce accurate corners and branch fittings.
مخاوف المنتج للعملاء
A pre-insulated duct must preserve an uninterrupted vapor barrier and protect its foam edges from air leakage, moisture and jobsite damage.
Separate metal duct and insulation increase ceiling load and labor.One rigid PIR panel performs as the duct wall and thermal insulation layer.
Foil cuts at corners become paths for condensation moisture.Continuous foil tape, formed corner profiles and compatible sealant close every exposed edge.
Foam panels are damaged around hangers and service openings.Load-spreading support saddles and reinforced penetrations protect the low-density core.
Field-made joints vary in alignment and air tightness.Matched edge profiles and controlled cutting templates produce repeatable section geometry.
تطبيقات نموذجية
Indoor cleanroom supply ductsReturn-air distributionLow-load suspended ceiling routesHumidity-controlled HVAC branchesPrefabricated mechanical modules
المعلمات الفنية
Typical material data for aluminum-faced PIR pre-insulated duct panels are listed below.
| المواد الأساسية | Closed-cell polyisocyanurate (PIR) rigid foam |
|---|---|
| سمك اللوحة | 20–30 mm |
| العرض الفعال | 1200 mm standard panel width |
| الحد الأقصى الطول | 4000 mm standard panel length |
| الصلب يواجه سمك | 0.06–0.20 mm embossed aluminum foil facing on each side |
| الكثافة الأساسية | 45–55 kg/m³ |
| الموصلية الحرارية | 0.020–0.023 W/(m·K) at approximately 10–25°C mean temperature |
| إنهاء السطح | Embossed or smooth aluminum foil laminate on internal and external faces |
| نوع المشترك | Male-female panel joint with aluminum profile, foil tape and vapor-tight sealant |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Antimicrobial coated interior foilReinforced external aluminum facingFlanged equipment connection profilesRectangular fittings and branch modules
Planning a PIR Pre-Insulated Air Duct specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
