English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
إضاءة الغرف النظيفة والمعدات الكهربائية
Isolation محول
A dry-type transformer that provides galvanic separation, voltage adaptation and optional electrostatic shielding for sensitive cleanroom loads.
- Galvanically Isolated Windings
- Low-Noise Laminated Core
- Electrostatic Shield Option
- Enclosed Finger-Safe Terminals
مقدمة المنتج
The isolation transformer uses separate primary and secondary windings on a laminated magnetic core. Encapsulated or varnish-impregnated coils resist moisture and vibration, and an optional copper electrostatic shield is bonded to earth between windings to attenuate common-mode noise. The assembly is housed in a non-ventilated or guarded enclosure with clearly separated input and output terminals.
الخصائص الرئيسية
Encapsulated coils support consistent insulation and lower audible vibration.
An interwinding shield diverts coupled high-frequency noise to protective earth.
Finger-safe terminal blocks organize primary taps and secondary connections.
Rubber isolation mounts reduce mechanical hum transmitted to the floor or wall.
مخاوف المنتج للعملاء
Sensitive equipment can be affected by ground noise, voltage mismatch and transformer hum even when the nominal supply remains available.
Common-mode electrical noise enters instrument reference circuits.Galvanic separation and an optional grounded shield reduce capacitive noise transfer.
A transformer enclosure transmits audible hum into a quiet laboratory.A welded core, coil impregnation and resilient mounting pads limit vibration.
Exposed terminal studs create accidental-contact risk.A guarded wiring compartment uses labeled finger-safe connectors.
Dust enters an open ventilated enclosure near a clean process.An encapsulated non-ventilated configuration closes the core and coil from room air.
تطبيقات نموذجية
Sensitive analytical instrumentsCleanroom control powerMedical-device test benchesNoise-sensitive monitoring systems
المعلمات الفنية
Typical configurable construction ranges for an isolation transformer are listed below.
| المواد الأساسية | Grain-oriented silicon-steel core with separate copper windings, insulation system and optional copper electrostatic shield |
|---|---|
| سمك اللوحة | 200-650 mm enclosed transformer depth |
| العرض الفعال | 250-900 mm cabinet width |
| الحد الأقصى الطول | Up to 1200 mm overall enclosure height |
| الصلب يواجه سمك | 1.0-2.0 mm powder-coated steel or stainless enclosure |
| الكثافة الأساسية | Approximately 7600-7700 kg/m³ for laminated electrical steel core material |
| الموصلية الحرارية | 20-30 W/(m·K) for laminated silicon steel across the core assembly |
| إنهاء السطح | Light-grey or white powder-coated enclosure with copper earth and terminal markings |
| نوع المشترك | Bolted or welded core-and-coil assembly on resilient mounts with segregated terminal compartment |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Single- or three-phase designEncapsulated or ventilated dry typeElectrostatic shieldInput and output voltage tap selection
Planning a Isolation Transformer specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
