English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
معدات تهوية وتكييف ومعالجة الهواء في الغرف النظيفة
برج التبريد المضاد للتدفق المستحث
A compact evaporative heat-rejection tower that draws air upward through wetted fill while condenser water descends into an accessible collection basin.
- Counterflow Air-Water Contact
- Top-Mounted Induced Draft
- Corrosion-Resistant FRP Shell
- Serviceable Fill and Basin
مقدمة المنتج
The induced-draft counterflow tower uses a top axial fan to draw ambient air upward against warm condenser water distributed above the fill. Evaporation removes heat before cooled water collects in the lower basin and returns to the refrigeration plant. A square FRP casing, removable louvers and modular fill pack provide a compact alternative to crossflow arrangements where footprint matters.
الخصائص الرئيسية
The fan at the discharge draws air uniformly through lower inlet louvers and reduces recirculation at the intake.
FRP casing panels and stainless support members resist continuous wet service and treatment chemistry.
Access doors, removable fill cassettes and an open basin support inspection of water-contact components.
مخاوف المنتج للعملاء
A cooling tower must reject the design load while controlling footprint, water distribution and maintenance access.
Limited roof area restricts the size of heat-rejection equipment.A vertical counterflow path concentrates fill depth and fan discharge within a compact square plan.
Uneven spray distribution leaves dry fill zones and reduces capacity.A full-coverage header and serviceable nozzles wet the modular fill pack uniformly.
Drift can carry treatment chemicals beyond the tower.Dedicated drift eliminators change exhaust-air direction and capture entrained droplets.
Basin sediment blocks strainers and accelerates corrosion.Accessible sloped basin surfaces, drain points and removable strainers simplify routine cleaning.
تطبيقات نموذجية
Cleanroom chiller condenser-water systemsPharmaceutical process-cooling loopsHospital central plantsElectronics-factory HVACIndustrial refrigeration heat rejection
المعلمات الفنية
Representative physical construction ranges for a modular counterflow tower are listed below.
| المواد الأساسية | PVC fill media inside fiber-reinforced polymer casing |
|---|---|
| سمك اللوحة | 3-6 mm molded FRP casing panel thickness |
| العرض الفعال | 1000-3200 mm nominal tower cell width |
| الحد الأقصى الطول | Up to 6500 mm for multi-cell assemblies |
| الصلب يواجه سمك | 1.5-3.0 mm stainless or hot-dip-galvanized basin/support sheet |
| الكثافة الأساسية | 30-60 kg/m³ typical PVC fill-pack density |
| الموصلية الحرارية | Approximately 0.19 W/(m·K) for rigid PVC fill material |
| إنهاء السطح | Smooth UV-stabilized FRP exterior with passivated or galvanized hardware |
| نوع المشترك | Bolted gasketed casing panels with modular clipped fill cassettes and flanged water ports |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Single-cell or multi-cell configurationPVC or higher-temperature polypropylene fillVariable-speed fan drive and vibration switchStainless basin, electric basin heater and low-noise fan
Planning a Induced-Draft Counterflow Cooling Tower specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
