İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda HVAC ve Hava İşleme Ekipmanları
Induced-Draft Counterflow Soğutma Kulesi
A compact evaporative heat-rejection tower that draws air upward through wetted fill while condenser water descends into an accessible collection basin.
- Counterflow Air-Water Contact
- Top-Mounted Induced Draft
- Corrosion-Resistant FRP Shell
- Serviceable Fill and Basin
Ürün tanıtımı
The induced-draft counterflow tower uses a top axial fan to draw ambient air upward against warm condenser water distributed above the fill. Evaporation removes heat before cooled water collects in the lower basin and returns to the refrigeration plant. A square FRP casing, removable louvers and modular fill pack provide a compact alternative to crossflow arrangements where footprint matters.
Ana Özellikler
The fan at the discharge draws air uniformly through lower inlet louvers and reduces recirculation at the intake.
FRP casing panels and stainless support members resist continuous wet service and treatment chemistry.
Access doors, removable fill cassettes and an open basin support inspection of water-contact components.
Müşteri Ürün Sorunları
A cooling tower must reject the design load while controlling footprint, water distribution and maintenance access.
Limited roof area restricts the size of heat-rejection equipment.A vertical counterflow path concentrates fill depth and fan discharge within a compact square plan.
Uneven spray distribution leaves dry fill zones and reduces capacity.A full-coverage header and serviceable nozzles wet the modular fill pack uniformly.
Drift can carry treatment chemicals beyond the tower.Dedicated drift eliminators change exhaust-air direction and capture entrained droplets.
Basin sediment blocks strainers and accelerates corrosion.Accessible sloped basin surfaces, drain points and removable strainers simplify routine cleaning.
Tipik uygulamalar
Cleanroom chiller condenser-water systemsPharmaceutical process-cooling loopsHospital central plantsElectronics-factory HVACIndustrial refrigeration heat rejection
Teknik parametreler
Representative physical construction ranges for a modular counterflow tower are listed below.
| Temel malzemeler | PVC fill media inside fiber-reinforced polymer casing |
|---|---|
| Panel kalınlığı | 3-6 mm molded FRP casing panel thickness |
| Effective Width (Etkili Genişlik) | 1000-3200 mm nominal tower cell width |
| Maksimum uzunluk | Up to 6500 mm for multi-cell assemblies |
| Çelik yüz yüze kalınlığı | 1.5-3.0 mm stainless or hot-dip-galvanized basin/support sheet |
| Core Density (Çekirdek Yoğunluğu) | 30-60 kg/m³ typical PVC fill-pack density |
| Termal İletkenlik | Approximately 0.19 W/(m·K) for rigid PVC fill material |
| Yüzey bitirme | Smooth UV-stabilized FRP exterior with passivated or galvanized hardware |
| Ortak tip | Bolted gasketed casing panels with modular clipped fill cassettes and flanged water ports |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
Single-cell or multi-cell configurationPVC or higher-temperature polypropylene fillVariable-speed fan drive and vibration switchStainless basin, electric basin heater and low-noise fan
Planning a Induced-Draft Counterflow Cooling Tower specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
