English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
ОВК и оборудование для обработки воздуха в чистых помещениях
Индуцированная контртоковая охлаждающая башня
A compact evaporative heat-rejection tower that draws air upward through wetted fill while condenser water descends into an accessible collection basin.
- Counterflow Air-Water Contact
- Top-Mounted Induced Draft
- Corrosion-Resistant FRP Shell
- Serviceable Fill and Basin
Введение продукции
The induced-draft counterflow tower uses a top axial fan to draw ambient air upward against warm condenser water distributed above the fill. Evaporation removes heat before cooled water collects in the lower basin and returns to the refrigeration plant. A square FRP casing, removable louvers and modular fill pack provide a compact alternative to crossflow arrangements where footprint matters.
Основные характеристики
The fan at the discharge draws air uniformly through lower inlet louvers and reduces recirculation at the intake.
FRP casing panels and stainless support members resist continuous wet service and treatment chemistry.
Access doors, removable fill cassettes and an open basin support inspection of water-contact components.
Обеспокоенность клиентов продуктами
A cooling tower must reject the design load while controlling footprint, water distribution and maintenance access.
Limited roof area restricts the size of heat-rejection equipment.A vertical counterflow path concentrates fill depth and fan discharge within a compact square plan.
Uneven spray distribution leaves dry fill zones and reduces capacity.A full-coverage header and serviceable nozzles wet the modular fill pack uniformly.
Drift can carry treatment chemicals beyond the tower.Dedicated drift eliminators change exhaust-air direction and capture entrained droplets.
Basin sediment blocks strainers and accelerates corrosion.Accessible sloped basin surfaces, drain points and removable strainers simplify routine cleaning.
Типичные приложения
Cleanroom chiller condenser-water systemsPharmaceutical process-cooling loopsHospital central plantsElectronics-factory HVACIndustrial refrigeration heat rejection
Технические параметры
Representative physical construction ranges for a modular counterflow tower are listed below.
| Основной материал | PVC fill media inside fiber-reinforced polymer casing |
|---|---|
| Толщина панели | 3-6 mm molded FRP casing panel thickness |
| эффективная ширина | 1000-3200 mm nominal tower cell width |
| Максимальная длина | Up to 6500 mm for multi-cell assemblies |
| Толщина линий стали | 1.5-3.0 mm stainless or hot-dip-galvanized basin/support sheet |
| Плотность ядра | 30-60 kg/m³ typical PVC fill-pack density |
| Теплопроводимость | Approximately 0.19 W/(m·K) for rigid PVC fill material |
| Поверхностная отделка | Smooth UV-stabilized FRP exterior with passivated or galvanized hardware |
| Объединенный тип | Bolted gasketed casing panels with modular clipped fill cassettes and flanged water ports |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Single-cell or multi-cell configurationPVC or higher-temperature polypropylene fillVariable-speed fan drive and vibration switchStainless basin, electric basin heater and low-noise fan
Planning a Induced-Draft Counterflow Cooling Tower specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
