English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة الجدار والسقف للغرفة النظيفة
HPL لوحة بطانة الحائط غرف الأبحاث
A compact high-pressure laminate lining system fixed over an existing wall, creating a hard, moisture-tolerant and easy-to-wipe cleanroom surface without building a second insulated partition.
- 12 mm Compact HPL Face
- Concealed Mechanical Supports
- Impact-Resistant Wall Upgrade
- Sealed Vertical Connections
مقدمة المنتج
HPL Cleanroom Wall Liner Panels use a homogeneous compact laminate sheet carried on concealed aluminum support profiles. The liner sits in front of masonry, concrete or framed construction and converts the substrate into a smooth controlled-environment finish. Interlocking vertical profiles hold each sheet without exposed front fasteners, while the recessed base detail can meet a sheet-vinyl or resin floor with minimal ledges. Because the sheet itself is dense and self-supporting, the system does not depend on a foam or mineral insulation core.
الخصائص الرئيسية
Mechanical attachment avoids wet bonding over the entire existing wall surface.
Concealed vertical profiles keep screws and clips away from the cleanable face.
Compact HPL can be machined for sockets, controls and service penetrations before fitting.
Individual sheets remain accessible for localized replacement after surface damage.
مخاوف المنتج للعملاء
Wall-lining buyers focus on substrate irregularity, edge moisture, visible fasteners and repair access in occupied facilities.
Uneven masonry produces visible waves when thin decorative sheets are bonded directly to it.Adjustable vertical supports establish a straight plane before the compact laminate is attached.
Open HPL edges can absorb moisture or collect residue near floors and service holes.Recessed base profiles, closed cut-out trims and continuous joint sealant protect exposed edges.
Surface screws create cleaning obstructions across a newly lined wall.Interlocking rear profiles retain the sheets while leaving the room face free of visible mechanical fixings.
A damaged section of permanently bonded cladding is difficult to remove neatly.Modular support profiles allow one liner sheet to be released without stripping the complete elevation.
تطبيقات نموذجية
HPL laboratory lining upgradesPharmaceutical support roomsHospital clean corridorsMedical-device assembly areasGowning and personnel-change rooms
المعلمات الفنية
Common production dimensions for compact HPL cleanroom liner systems are listed below.
| المواد الأساسية | N/A — homogeneous compact high-pressure laminate has no separate core |
|---|---|
| سمك اللوحة | 12 mm |
| العرض الفعال | 1286 mm |
| الحد الأقصى الطول | 3000 mm |
| الصلب يواجه سمك | N/A — compact HPL liner has no steel facing |
| الكثافة الأساسية | N/A — the liner is a solid laminate sheet rather than a low-density core panel |
| الموصلية الحرارية | N/A — wall liner is not used as a thermal-insulation component |
| إنهاء السطح | Smooth low-texture compact HPL in cleanroom white or selected solid colour |
| نوع المشترك | Concealed interlocking vertical supports with 20 × 30 mm joint tube and sealed face joint |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
Recessed or floor-reaching base detailAlternative solid HPL coloursPre-machined utility openingsInternal corner and end-closure profiles
Planning a HPL Cleanroom Wall Liner Panel specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
