English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
اكسسوارات تركيب الغرف النظيفة
Duct شماعات
An adjustable galvanized trapeze hanger with two threaded rods and a slotted channel crossbar for suspending rectangular cleanroom ductwork.
- Twin Threaded Rods
- Slotted Channel Crossbar
- Independent Level Adjustment
- Galvanized Steel Hardware
مقدمة المنتج
The duct hanger forms a rigid trapeze below the structural attachment points. Two continuously threaded rods pass through the ends of a galvanized slotted C-channel and are retained by paired nuts and washers, allowing installers to set crossbar elevation and level before the duct is seated. The open channel accepts compatible saddles or restraint hardware without requiring holes to be drilled through the supported duct casing.
الخصائص الرئيسية
A slotted C-channel permits flexible positioning of compatible duct restraint hardware.
Broad washer stacks distribute clamping load at the rod-to-channel interfaces.
Zinc-plated steel offers a practical finish for dry indoor service plenums.
مخاوف المنتج للعملاء
Rectangular duct runs require a level, distributed support that can be adjusted around uneven overhead structure without puncturing the duct casing.
Fixed-length hangers make it difficult to level ductwork below an uneven soffit.Independent nuts on the two threaded rods allow each end of the channel to be adjusted separately.
Narrow point supports can distort light-gauge rectangular duct walls.The channel crossbar provides a continuous bearing line beneath the duct or its support saddle.
Drilling the duct casing creates avoidable leakage and contamination traps.The trapeze supports the duct externally and accepts separate restraint hardware through its slots.
Bare carbon-steel hardware can develop surface corrosion in service voids.Galvanized or stainless hardware can be selected to suit the plenum exposure.
تطبيقات نموذجية
Rectangular cleanroom supply duct suspensionReturn-air duct trapeze supportsExhaust duct support framesAir-handler connection supportService-plenum HVAC installations
المعلمات الفنية
Typical construction ranges for an adjustable galvanized cleanroom duct trapeze hanger are listed below.
| المواد الأساسية | Galvanized carbon-steel C-channel, threaded rods, nuts, washers and anchor plates |
|---|---|
| سمك اللوحة | 0.60-2.00 mm compatible rectangular duct wall thickness |
| العرض الفعال | 200-1500 mm adjustable duct support width |
| الحد الأقصى الطول | Up to 2000 mm slotted channel crossbar length |
| الصلب يواجه سمك | 1.50-3.00 mm nominal channel wall thickness |
| الكثافة الأساسية | Approximately 7850 kg/m³ for carbon-steel components |
| الموصلية الحرارية | Approximately 45-60 W/(m·K) for carbon steel |
| إنهاء السطح | Silver electro-galvanized or hot-dip galvanized steel |
| نوع المشترك | Twin threaded-rod trapeze with nut-and-washer clamped slotted channel |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
M8, M10 or M12 threaded rodsElectro-galvanized, hot-dip galvanized or stainless steelCustom crossbar width and slot patternOptional elastomer isolation strip or duct saddle
Planning a Duct Hanger specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
