Bahasa Inggris
Bahasa Jerman
Bahasa Arab
Bahasa Perancis: Bahasa Perancis
Bahasa IndonesiaSaat ini
Bahasa Jepang
Bahasa Korea
Bahasa Melayu
Bahasa Portugis
Bahasa Rusia
Bahasa Spanyol
Bahasa Thailand
Bahasa Turki
Bahasa Vietnam
Aksesoris Instalasi Cleanroom
Duct gantungan
An adjustable galvanized trapeze hanger with two threaded rods and a slotted channel crossbar for suspending rectangular cleanroom ductwork.
- Twin Threaded Rods
- Slotted Channel Crossbar
- Independent Level Adjustment
- Galvanized Steel Hardware
Perkenalan produk
The duct hanger forms a rigid trapeze below the structural attachment points. Two continuously threaded rods pass through the ends of a galvanized slotted C-channel and are retained by paired nuts and washers, allowing installers to set crossbar elevation and level before the duct is seated. The open channel accepts compatible saddles or restraint hardware without requiring holes to be drilled through the supported duct casing.
Fitur utama:
A slotted C-channel permits flexible positioning of compatible duct restraint hardware.
Broad washer stacks distribute clamping load at the rod-to-channel interfaces.
Zinc-plated steel offers a practical finish for dry indoor service plenums.
Kekhawatiran produk pelanggan
Rectangular duct runs require a level, distributed support that can be adjusted around uneven overhead structure without puncturing the duct casing.
Fixed-length hangers make it difficult to level ductwork below an uneven soffit.Independent nuts on the two threaded rods allow each end of the channel to be adjusted separately.
Narrow point supports can distort light-gauge rectangular duct walls.The channel crossbar provides a continuous bearing line beneath the duct or its support saddle.
Drilling the duct casing creates avoidable leakage and contamination traps.The trapeze supports the duct externally and accepts separate restraint hardware through its slots.
Bare carbon-steel hardware can develop surface corrosion in service voids.Galvanized or stainless hardware can be selected to suit the plenum exposure.
Aplikasi yang Tipis
Rectangular cleanroom supply duct suspensionReturn-air duct trapeze supportsExhaust duct support framesAir-handler connection supportService-plenum HVAC installations
Parameter teknis
Typical construction ranges for an adjustable galvanized cleanroom duct trapeze hanger are listed below.
| Bahan inti | Galvanized carbon-steel C-channel, threaded rods, nuts, washers and anchor plates |
|---|---|
| Ketebalan Panel (Panel Thickness) | 0.60-2.00 mm compatible rectangular duct wall thickness |
| Efektif lebar | 200-1500 mm adjustable duct support width |
| Panjang maksimum | Up to 2000 mm slotted channel crossbar length |
| Baja menghadap ketebalan | 1.50-3.00 mm nominal channel wall thickness |
| Kepadatan inti (core density) | Approximately 7850 kg/m³ for carbon-steel components |
| Konduktivitas Termal (Thermal Conductivity) | Approximately 45-60 W/(m·K) for carbon steel |
| Permukaan selesai | Silver electro-galvanized or hot-dip galvanized steel |
| Jenis Bersama | Twin threaded-rod trapeze with nut-and-washer clamped slotted channel |
| Customization (Kustomisasi) | Tersedia berdasarkan aplikasi yang dimaksudkan dan lingkungan operasi. |
Pilihan yang tersedia
M8, M10 or M12 threaded rodsElectro-galvanized, hot-dip galvanized or stainless steelCustom crossbar width and slot patternOptional elastomer isolation strip or duct saddle
Planning a Duct Hanger specification?
Kirimkan kami dimensi Anda, kondisi instalasi, target kinerja dan permukaan akhir yang diperlukan.
