İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda zemin sistemleri
Seamless Epoxy Cove Base
A vertical-grade, aggregate-filled epoxy mortar shaped into an integral radius between resin flooring and adjacent walls, curbs or equipment bases.
- Integral Resin Transition
- Sag-Resistant Cove Mortar
- 25 mm Formed Radius
- Abrasion-Resistant Finish
Ürün tanıtımı
The seamless epoxy cove base extends a resin floor upward with a hand-trowelled mortar composed of epoxy binder and graded aggregate. Its vertical-grade consistency holds the required height and radius without slumping while it cures. A keyed chase or non-corroding cap strip defines the upper termination, and the finished cove can receive a compatible resin seal coat to match the floor. The same material can be formed around equipment pads, kerbs and columns where a square internal corner would obstruct cleaning.
Ana Özellikler
A formed radius links floor and wall surfaces without inserting a separate flexible skirting component.
Fine graded aggregate builds impact and abrasion resistance at the exposed wall base.
Compatible resin seal coats coordinate colour and chemical exposure with the adjoining flooring system.
Müşteri Ürün Sorunları
An integral resin cove must hold its shape vertically, close the floor perimeter and remain compatible with the adjoining wearing system.
Standard flowing epoxy runs down the wall before a cove radius can cure.A vertical-grade mortar uses a thixotropic binder and aggregate blend that stays where it is trowelled.
A separate skirting strip creates upper and lower edges beside a monolithic resin floor.The epoxy mortar bonds directly to the prepared horizontal and vertical substrates as an integral cove.
Impacts from cleaning equipment chip a thin painted fillet at the wall base.A 3–6 mm aggregate-filled body provides a more substantial protected transition.
Uneven hand work produces inconsistent height and radius around the room.A level termination guide and sized cove trowel control the upper line and curved geometry.
Tipik uygulamalar
Pharmaceutical resin-floor perimetersCleanroom equipment plinthsLaboratory wall basesHygienic kerbs and column basesWash-down production rooms
Teknik parametreler
Typical construction data for a trowel-applied vertical epoxy cove mortar are listed below.
| Temel malzemeler | Three-component solvent-free epoxy binder with specially graded mineral aggregate |
|---|---|
| Panel kalınlığı | 3.0–6.0 mm nominal trowelled cove thickness |
| Effective Width (Etkili Genişlik) | 100 mm typical vertical cove height with a 25 mm internal radius |
| Maksimum uzunluk | Approximately 5800 mm nominal cove run per full kit at 100 mm height and 4 mm thickness |
| Çelik yüz yüze kalınlığı | 0 mm; the cove is an aggregate-filled epoxy mortar without steel facing |
| Core Density (Çekirdek Yoğunluğu) | Approximately 1810 kg/m³ for the combined epoxy cove mortar components |
| Termal İletkenlik | Approximately 0.25–0.40 W/(m·K) for cured aggregate-filled epoxy mortar |
| Yüzey bitirme | Fine trowelled texture with a compatible pigmented epoxy or polyurethane seal coat |
| Ortak tip | Integral bonded floor-to-wall radius terminated in a keyed chase or non-corroding cap strip |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
75–150 mm cove height25 or 38 mm internal radiusKeyed chase or metal cap-strip terminationColour-matched epoxy or polyurethane seal coat
Planning a Seamless Epoxy Cove Base specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
