İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda Hava Dağıtım Sistemleri
Manual Volume Control Damper
A locking quadrant damper with linked galvanized blades for setting and retaining the balancing position of a rectangular duct branch.
- Locking Manual Quadrant
- Opposed 3V Blade Bank
- Concealed Frame Linkage
- Permanent Branch Balancing
Ürün tanıtımı
The manual volume control damper places a bank of linked 3V blades inside a rigid galvanized channel frame. Turning the external quadrant rotates the blade shafts together, allowing the balancing technician to establish the required branch resistance and then lock the position mechanically. Opposed blade motion provides more even downstream velocity distribution than a single flap at intermediate positions. The drive linkage is enclosed within the frame, leaving the airway clear and protecting moving parts from accidental contact.
Ana Özellikler
Opposed 3V blades divide the throttling area across the full frame for smoother branch balancing.
Concealed linkage reduces obstruction in the airway and shields connecting bars from handling damage.
Channel-frame flange options support duct insertion, surface mounting or connection to an equipment opening.
Müşteri Ürün Sorunları
A manual damper should give the balancer fine position control, remain locked after commissioning and avoid creating a severely biased downstream velocity profile.
A loose handle creeps open after the branch has been balanced.A positive locking quadrant clamps the shaft at the recorded blade position.
A single large blade sends a concentrated jet toward one side of the downstream duct.Opposed blade operation divides the opening and produces a more distributed throttled flow.
External linkage is bent by insulation work or routine ceiling access.Link bars concealed inside the channel frame leave only the protected operator outside the casing.
The adjustment handle becomes buried beneath duct insulation.An extended shaft and stand-off quadrant preserve visible, reachable adjustment after insulation is applied.
Tipik uygulamalar
Cleanroom supply branch balancingGeneral exhaust duct commissioningAir-handling unit internal bypassesReturn-air grille branch controlFixed-volume process ventilation
Teknik parametreler
Typical construction data for a galvanized rectangular manual balancing damper are listed below.
| Temel malzemeler | Galvanized-steel 3V blades with plated steel shafts, concealed linkage and polymer bearings |
|---|---|
| Panel kalınlığı | 1.5 mm formed galvanized control blades |
| Effective Width (Etkili Genişlik) | 152–1219 mm nominal single-section frame width |
| Maksimum uzunluk | Up to 1880 mm single-section frame height |
| Çelik yüz yüze kalınlığı | 1.5 mm galvanized channel frame |
| Core Density (Çekirdek Yoğunluğu) | Approximately 7850 kg/m³ for galvanized steel blades |
| Termal İletkenlik | Approximately 45–55 W/(m·K) for the carbon-steel blade material |
| Yüzey bitirme | Mill-galvanized blade and frame surfaces with zinc-plated operating hardware |
| Ortak tip | Flanged channel frame with linked opposed blades and external locking quadrant |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
Parallel or opposed blade actionSingle, reversed or double flange frameExtended shaft for insulated ducts304 or 316 stainless-steel construction
Planning a Manual Volume Control Damper specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
