English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
Системы распределения воздуха в чистых помещениях
Ручной амортизатор управления объемом
A locking quadrant damper with linked galvanized blades for setting and retaining the balancing position of a rectangular duct branch.
- Locking Manual Quadrant
- Opposed 3V Blade Bank
- Concealed Frame Linkage
- Permanent Branch Balancing
Введение продукции
The manual volume control damper places a bank of linked 3V blades inside a rigid galvanized channel frame. Turning the external quadrant rotates the blade shafts together, allowing the balancing technician to establish the required branch resistance and then lock the position mechanically. Opposed blade motion provides more even downstream velocity distribution than a single flap at intermediate positions. The drive linkage is enclosed within the frame, leaving the airway clear and protecting moving parts from accidental contact.
Основные характеристики
Opposed 3V blades divide the throttling area across the full frame for smoother branch balancing.
Concealed linkage reduces obstruction in the airway and shields connecting bars from handling damage.
Channel-frame flange options support duct insertion, surface mounting or connection to an equipment opening.
Обеспокоенность клиентов продуктами
A manual damper should give the balancer fine position control, remain locked after commissioning and avoid creating a severely biased downstream velocity profile.
A loose handle creeps open after the branch has been balanced.A positive locking quadrant clamps the shaft at the recorded blade position.
A single large blade sends a concentrated jet toward one side of the downstream duct.Opposed blade operation divides the opening and produces a more distributed throttled flow.
External linkage is bent by insulation work or routine ceiling access.Link bars concealed inside the channel frame leave only the protected operator outside the casing.
The adjustment handle becomes buried beneath duct insulation.An extended shaft and stand-off quadrant preserve visible, reachable adjustment after insulation is applied.
Типичные приложения
Cleanroom supply branch balancingGeneral exhaust duct commissioningAir-handling unit internal bypassesReturn-air grille branch controlFixed-volume process ventilation
Технические параметры
Typical construction data for a galvanized rectangular manual balancing damper are listed below.
| Основной материал | Galvanized-steel 3V blades with plated steel shafts, concealed linkage and polymer bearings |
|---|---|
| Толщина панели | 1.5 mm formed galvanized control blades |
| эффективная ширина | 152–1219 mm nominal single-section frame width |
| Максимальная длина | Up to 1880 mm single-section frame height |
| Толщина линий стали | 1.5 mm galvanized channel frame |
| Плотность ядра | Approximately 7850 kg/m³ for galvanized steel blades |
| Теплопроводимость | Approximately 45–55 W/(m·K) for the carbon-steel blade material |
| Поверхностная отделка | Mill-galvanized blade and frame surfaces with zinc-plated operating hardware |
| Объединенный тип | Flanged channel frame with linked opposed blades and external locking quadrant |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Parallel or opposed blade actionSingle, reversed or double flange frameExtended shaft for insulated ducts304 or 316 stainless-steel construction
Planning a Manual Volume Control Damper specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
