Inglês
Alemão
Língua árabe
Francês
Língua indonésia
Japonês
Coreano
Língua malaia
Portuguêsatual
Língua russa
Espanhol
Tailandês
Língua turca
Vietnã
Equipamento de manuseio de ar e HVAC para sala limpa
Unidade de ventilador de alimentação de ar para sala limpa centrífuga EC
An insulated inline fan package using a direct-drive backward-curved EC impeller to deliver stable cleanroom supply airflow against filters, coils and distribution pressure losses.
- Backward-Curved EC Impeller
- Stepless Airflow Adjustment
- Insulated Low-Leakage Cabinet
- Vibration-Isolated Fan Module
Introdução do produto
The EC centrifugal supply-air fan unit places a high-efficiency backward-curved impeller, electronically commutated motor, airflow sensing and flexible connections inside a rigid insulated cabinet. Direct drive removes belts and their wear particles, while variable speed allows the fan to compensate for filter loading or switch between occupied and setback airflow. Removable panels provide access to the wheel, motor electronics and isolation mounts from outside the air path.
Características-chave
Integrated EC speed control accepts analog or network commands without an external variable-frequency drive for smaller fan sizes.
Flexible inlet and discharge connections prevent casing vibration from transferring into rigid cleanroom ductwork.
An insulated double-skin cabinet reduces breakout noise and limits condensation on the casing during cold supply-air operation.
Preocupações do produto do cliente
Cleanroom supply fans must overcome rising filter resistance while holding the scheduled airflow without adding unnecessary noise, vibration or maintenance debris.
Supply airflow falls as final filters accumulate dust, reducing room air changes and pressure.Closed-loop EC speed control increases fan output against the measured airflow or duct-pressure setpoint.
Belt dust and periodic tension adjustment are undesirable near a clean supply-air path.A direct-drive impeller eliminates belts, pulleys and routine belt alignment.
Fan vibration travels through the duct and becomes audible inside quiet cleanrooms.Spring or elastomer isolators and flexible connectors decouple the rotating assembly from the cabinet and duct.
A cramped plantroom prevents removal of the entire fan section for service.Large side panels expose the motor and wheel, while a slide-out fan base permits component replacement from one service side.
Aplicações típicas
Cleanroom AHU supply-fan replacement modulesFiltered make-up air booster systemsPharmaceutical production supply branchesLaboratory air-distribution pressure controlElectronics clean-bay ventilation
Parâmetros técnicos
Typical construction ranges for an insulated EC centrifugal supply-air fan package are listed below.
| Material principal | Aluminum or coated-steel backward-curved impeller in a mineral-wool-insulated galvanized steel cabinet |
|---|---|
| Painel de espessura | 30-50 mm double-skin acoustic and thermal panel thickness |
| Largura efetiva | 800-2400 mm nominal fan-cabinet width |
| Comprimento máximo | Up to 3500 mm for multi-fan or fan-plus-silencer assemblies |
| Aço enfrentando espessura | 0.8-1.2 mm pre-painted outer skin and galvanized inner skin |
| Densidade Core | 40-80 kg/m³ typical mineral-wool cabinet insulation density |
| Condutividade térmica | Approximately 0.035-0.045 W/(m·K) for mineral-wool cabinet insulation |
| Superfície acabado | White powder-coated frame with blue service doors and corrosion-resistant internal fan surfaces |
| Tipo conjunto | Bolted gasketed cabinet with flexible inlet and discharge connectors and vibration-isolated fan base |
| Customização | Disponível com base na aplicação pretendida e no ambiente operacional. |
Opções disponíveis
Single fan or parallel fan-array configurationConstant-airflow or constant-static-pressure controllerAcoustic attenuator and perforated inner linerGalvanized coated-aluminum or stainless air-path construction
Planning a EC Centrifugal Cleanroom Supply-Air Fan Unit specification?
Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.
