Inglês
Alemão
Língua árabe
Francês
Língua indonésia
Japonês
Coreano
Língua malaia
Portuguêsatual
Língua russa
Espanhol
Tailandês
Língua turca
Vietnã
Equipamento de sala limpa Peças de reposição
Substituição do filtro AHU
A rigid-header six-pocket air filter for replacing an established particulate stage in cleanroom and process air-handling units without changing the filter housing.
- Six Tapered Filter Pockets
- Rigid Galvanized Header
- Extended Media Area
- Matched Gasket Options
Introdução do produto
The AHU replacement filter is an extended-surface pocket filter installed in a front- or side-access filter bank. Six tapered glass-fiber bags increase usable media area behind a standard square header while internal seams keep the pockets separated as airflow develops. A folded galvanized-steel frame holds the pocket mouths square, and a continuous perimeter gasket can seal the header against the retaining frame. Replacement selection must reproduce the existing face dimensions, pocket depth, filter stage, airflow direction and gasket location so the new filter seats correctly without bypass or interference inside the air-handling unit.
Características-chave
The folded galvanized-steel header resists handling distortion during removal, transport and clamping in the filter bank.
Separated pocket seams reduce crowding between adjacent bags and preserve open media area under operating airflow.
Optional flat perimeter gaskets support a continuous compression seal on the specified upstream or downstream header face.
Preocupações do produto do cliente
A pocket filter can fit the opening yet still perform poorly when its depth, pocket layout or sealing arrangement differs from the original module.
An incorrect face size or header depth prevents the replacement from seating beneath the existing clamps.Module width, height, header depth and retaining-frame clearance are matched to the removed filter before manufacture.
Bags that are too long can contact coils, dampers or the next filter stage inside a shallow AHU section.Pocket depth and installed airflow direction are selected to preserve the measured downstream service clearance.
A missing or misplaced gasket allows unfiltered air to bypass the media around the header.Gasket material, face location and continuity are configured for the actual sealing surface in the filter bank.
Poor pocket separation causes adjacent bags to crowd together and reduces effective media exposure.Tapered pocket geometry and continuous internal separators hold six flow paths open across the module.
Aplicações típicas
Cleanroom make-up and recirculation AHUsProcess ventilation filter banksHEPA prefiltration stagesCommercial and industrial HVAC maintenance
Parâmetros técnicos
The ranges below describe common rigid-header pocket filters used as replaceable AHU stages; final dimensions and media selection are matched to the installed filter bank.
| Material principal | Air-laid glass-fiber pocket media with galvanized-steel header and optional elastomer perimeter gasket |
|---|---|
| Painel de espessura | 20-25 mm nominal folded header depth |
| Largura efetiva | 287-592 mm nominal filter module width |
| Comprimento máximo | Up to 640 mm pocket depth |
| Aço enfrentando espessura | 0.5-0.8 mm nominal galvanized-steel header sheet |
| Densidade Core | 16-40 kg/m³ for representative low-density bonded glass-fiber media |
| Condutividade térmica | 0.032-0.046 W/(m·K) for representative low-density glass-fiber media |
| Superfície acabado | Natural galvanized-silver header, clean white glass-fiber pockets and optional black flat gasket |
| Tipo conjunto | Sealed six-pocket assembly retained in a folded double-U header with compression-gasket seating |
| Customização | Disponível com base na aplicação pretendida e no ambiente operacional. |
Opções disponíveis
Matched full-size or half-size module370-640 mm pocket depthAlternative pocket count and media gradeUpstream, downstream or circumferential gasket
Planning a AHU Replacement Filter specification?
Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.
