English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة الجدار والسقف للغرفة النظيفة
غرف الأبحاث الداخلية غطاء الملف الشخصي
A radiused two-part aluminum cove that replaces a sharp internal junction with a smooth, cleanable transition inside controlled rooms.
- Smooth 50 mm internal radius
- Two-part clip-on construction
- Cleanable powder-coated surface
- Suitable for wall, floor and ceiling junctions
مقدمة المنتج
The Internal Cleanroom Coving Profile forms a continuous concave radius where two room surfaces meet. A concealed backing section is fixed first, then the finished cove face clips into position to cover fasteners and bridge the junction. The rounded geometry makes wiping easier than a tight square corner and can remain in place while compatible wall panels are removed from nearby bays.
الخصائص الرئيسية
A separate backing channel keeps primary fixings behind the finished face.
Clip-on assembly creates an even exposed line along long room junctions.
Powder-coated aluminum tolerates routine wipe-down cleaning.
Matching end caps and three-way pieces can finish intersecting cove runs.
مخاوف المنتج للعملاء
Sharp internal corners are awkward to wipe, visually emphasize sealant irregularities and can collect residue at the meeting point of two surfaces.
Cleaning cloths cannot maintain full contact inside a tight 90-degree recess.A 50 mm concave radius creates a broad, accessible wiping path.
Exposed fixings interrupt the surface at a hygiene-critical junction.The finished cove snaps over its backing channel and conceals the attachment points.
Hand-formed corner sealant often varies in width and appearance.A factory-extruded face establishes a uniform radius along the entire run.
Complex corner intersections require improvised cuts that are hard to seal neatly.Compatible end, internal and three-way accessories provide shaped termination pieces.
تطبيقات نموذجية
Wall-to-ceiling cleanroom junctionsWall-to-wall internal cornersWall-to-floor perimeter transitionsHygienic laboratory interiorsPharmaceutical processing rooms
المعلمات الفنية
This profile is a finishing component rather than an insulated panel. Its defining dimension is the internal radius and its material properties come from the aluminum extrusion.
| المواد الأساسية | Two-part 6063 aluminum backing channel and cove face |
|---|---|
| سمك اللوحة | N/A — not applicable to an internal coving profile |
| العرض الفعال | 50 mm standard internal cove radius |
| الحد الأقصى الطول | 3000 mm |
| الصلب يواجه سمك | N/A — the profile is extruded aluminum |
| الكثافة الأساسية | N/A — no insulated core; aluminum alloy density is approximately 2700 kg/m³ |
| الموصلية الحرارية | N/A — no insulated core; aluminum alloy is approximately 200 W/(m·K) |
| إنهاء السطح | White polyester powder-coated or clear anodized |
| نوع المشترك | Snap-on cove face over a concealed backing channel with sealed edges |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
50 mm radius internal coveAlternative 75 mm radiusThree-way internal corner pieceEnd caps and matching sealed transitions
Planning a Internal Cleanroom Coving Profile specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
