English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
غرف الأبحاث معدات قطع الغيار
FFU تحكم السرعة
A compact panel-mounted controller that gives operators direct, stepless airflow adjustment for compatible EC-motor fan filter units.
- Stepless Manual Adjustment
- EC Fan Signal Control
- Compact Panel Mounting
- Serviceable Screw Terminals
مقدمة المنتج
The FFU speed controller provides a local setpoint for a compatible electronically commutated fan motor. Turning the front potentiometer varies the low-voltage command used by the motor electronics, allowing commissioning or maintenance personnel to trim airflow without replacing the FFU drive. The molded enclosure protects the control components, while mounting ears and a removable screw terminal block simplify installation near the fan housing or inside a control compartment. Signal range, terminal assignment and minimum-speed behavior must be matched to the existing motor or FFU control card.
الخصائص الرئيسية
Low-voltage signal architecture is suited to EC fans that accept an analog speed command.
Front status indication provides a quick visual check that the control circuit is energized.
Screw terminals and external mounting tabs support straightforward replacement and servicing.
مخاوف المنتج للعملاء
A replacement speed controller must produce the signal expected by the installed motor and fit the existing wiring and mounting arrangement.
The new controller uses a signal range that the existing EC motor cannot interpret correctly.The controller is selected to match the motor's specified analog command range and reference supply.
Airflow falls below the stable operating point at the lowest dial position.Minimum-speed behavior can be matched or preset to preserve the required lower airflow limit.
Different terminal assignments create wiring errors during field replacement.Terminal count, signal common, reference voltage and command output are verified against the original connection diagram.
The control cannot be secured near the FFU without modifying the housing.Mounting-tab geometry and enclosure orientation can be configured for the available service space.
تطبيقات نموذجية
Single FFU airflow commissioningوحدات تصفية مروحة سقف غرف الأبحاثLaminar-flow workstation fansLocal EC fan maintenance control
المعلمات الفنية
Typical construction ranges for compact manual FFU speed controllers are shown below.
| المواد الأساسية | Flame-retardant PC/ABS enclosure with FR-4 control board and copper-alloy terminals |
|---|---|
| سمك اللوحة | 35-70 mm nominal enclosure depth |
| العرض الفعال | 70-135 mm nominal mounting width |
| الحد الأقصى الطول | Up to 160 mm overall length including mounting tabs |
| الصلب يواجه سمك | 0.8-1.5 mm equivalent terminal-clamp and internal bracket thickness |
| الكثافة الأساسية | 1050-1250 kg/m³ for molded PC/ABS enclosure material |
| الموصلية الحرارية | 0.18-0.25 W/(m·K) for molded enclosure material |
| إنهاء السطح | Fine-textured matte-black housing with white dial marks, green indicator and green terminal block |
| نوع المشترك | Six-position screw terminal connection with bolted external mounting tabs |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
0-10 V or matched potentiometer interfaceMinimum-speed presetAlternative terminal assignmentCustom mounting-tab geometry
Planning a FFU Speed Controller specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
