English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
FFU ومعدات تنقية الهواء الطرفية
FFU
A floor-standing control cabinet that supervises multiple FFU zones through an industrial HMI, protected power distribution and building-network communication.
- Multi-Zone HMI Control
- Central Alarm Overview
- Operating Data Logging
- BACnet or Modbus Interface
مقدمة المنتج
The FFU central control system consolidates cleanroom fan commands, feedback and alarms in a lockable electrical cabinet. An industrial touchscreen presents zone status, airflow or speed setpoints and maintenance warnings, while internal PLC, power supplies, circuit protection and network repeaters distribute commands to field-connected EC fan filter units. The architecture can place routine room operation on the HMI and pass selected points to the building management system. Separate power and communication terminals simplify commissioning and isolate a field wiring fault from the supervisory electronics.
الخصائص الرئيسية
PLC-based sequences can apply occupied, standby and recovery setpoints to different cleanroom areas.
Logged fan hours, alarm events and selected environmental points support maintenance planning.
Isolated BACnet or Modbus communication exchanges approved status and command points with the BMS.
مخاوف المنتج للعملاء
A large FFU installation becomes difficult to operate when individual units lack common setpoints, fault visibility and a controlled interface to the building system.
Operators walk through multiple rooms to change hundreds of local fan settings.The central HMI applies commands to defined FFU zones from one supervised interface.
A failed fan remains unnoticed until particle control is affected.Motor feedback and communication alarms identify the affected address and zone promptly.
Night operation consumes full fan power even when contamination loads are low.Scheduled occupied and standby modes reduce selected EC fan setpoints without shutting down monitoring.
Direct BMS commands can conflict with local cleanroom operating sequences.A defined gateway exposes selected points while the PLC retains interlocks and command priorities.
تطبيقات نموذجية
Large semiconductor FFU ceilingsMulti-room pharmaceutical facilitiesBattery dry-room clean zonesDisplay and optics manufacturingCentral cleanroom operations centres
المعلمات الفنية
Representative enclosure and electronics ranges for an FFU central control system are listed below.
| المواد الأساسية | Industrial PLC, touchscreen HMI, 24 VDC power supplies, protected distribution and isolated RS-485/Ethernet gateways |
|---|---|
| سمك اللوحة | 180-300 mm control-cabinet depth |
| العرض الفعال | 600-1000 mm nominal cabinet width |
| الحد الأقصى الطول | Up to 1800 mm cabinet height for expanded power and communication sections |
| الصلب يواجه سمك | 1.5-2.0 mm powder-coated steel enclosure and hinged front door |
| الكثافة الأساسية | Approximately 1800-1900 kg/m³ nominal density of the FR-4 substrate used in the central control board |
| الموصلية الحرارية | Approximately 0.25-0.40 W/(m·K) through the FR-4 substrate inside the FFU central controller |
| إنهاء السطح | Light-grey or cleanroom-white epoxy-polyester powder-coated cabinet with sealed HMI bezel |
| نوع المشترك | Gasketed hinged door, DIN-rail terminal blocks, separated gland plates and pluggable field connectors |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Wall-mount or floor-standing cabinetBACnet MS/TP, Modbus RTU or Ethernet gatewayDifferential pressure and temperature inputsRemote web dashboard and event logging
Planning a FFU Central Control System specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
