English
Немецкий
Арабский язык
Французский
Индонезийский
Японский язык
Корейский
Японский
Португальский
Русский языкТекущий
Испанский язык
Тайский
Турецкий
Вьетнамский язык
УФУ и терминальное оборудование для очистки воздуха
Система централизованного управления ФГУ
A floor-standing control cabinet that supervises multiple FFU zones through an industrial HMI, protected power distribution and building-network communication.
- Multi-Zone HMI Control
- Central Alarm Overview
- Operating Data Logging
- BACnet or Modbus Interface
Введение продукции
The FFU central control system consolidates cleanroom fan commands, feedback and alarms in a lockable electrical cabinet. An industrial touchscreen presents zone status, airflow or speed setpoints and maintenance warnings, while internal PLC, power supplies, circuit protection and network repeaters distribute commands to field-connected EC fan filter units. The architecture can place routine room operation on the HMI and pass selected points to the building management system. Separate power and communication terminals simplify commissioning and isolate a field wiring fault from the supervisory electronics.
Основные характеристики
PLC-based sequences can apply occupied, standby and recovery setpoints to different cleanroom areas.
Logged fan hours, alarm events and selected environmental points support maintenance planning.
Isolated BACnet or Modbus communication exchanges approved status and command points with the BMS.
Обеспокоенность клиентов продуктами
A large FFU installation becomes difficult to operate when individual units lack common setpoints, fault visibility and a controlled interface to the building system.
Operators walk through multiple rooms to change hundreds of local fan settings.The central HMI applies commands to defined FFU zones from one supervised interface.
A failed fan remains unnoticed until particle control is affected.Motor feedback and communication alarms identify the affected address and zone promptly.
Night operation consumes full fan power even when contamination loads are low.Scheduled occupied and standby modes reduce selected EC fan setpoints without shutting down monitoring.
Direct BMS commands can conflict with local cleanroom operating sequences.A defined gateway exposes selected points while the PLC retains interlocks and command priorities.
Типичные приложения
Large semiconductor FFU ceilingsMulti-room pharmaceutical facilitiesBattery dry-room clean zonesDisplay and optics manufacturingCentral cleanroom operations centres
Технические параметры
Representative enclosure and electronics ranges for an FFU central control system are listed below.
| Основной материал | Industrial PLC, touchscreen HMI, 24 VDC power supplies, protected distribution and isolated RS-485/Ethernet gateways |
|---|---|
| Толщина панели | 180-300 mm control-cabinet depth |
| эффективная ширина | 600-1000 mm nominal cabinet width |
| Максимальная длина | Up to 1800 mm cabinet height for expanded power and communication sections |
| Толщина линий стали | 1.5-2.0 mm powder-coated steel enclosure and hinged front door |
| Плотность ядра | Approximately 1800-1900 kg/m³ nominal density of the FR-4 substrate used in the central control board |
| Теплопроводимость | Approximately 0.25-0.40 W/(m·K) through the FR-4 substrate inside the FFU central controller |
| Поверхностная отделка | Light-grey or cleanroom-white epoxy-polyester powder-coated cabinet with sealed HMI bezel |
| Объединенный тип | Gasketed hinged door, DIN-rail terminal blocks, separated gland plates and pluggable field connectors |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
Wall-mount or floor-standing cabinetBACnet MS/TP, Modbus RTU or Ethernet gatewayDifferential pressure and temperature inputsRemote web dashboard and event logging
Planning a FFU Central Control System specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
