Three-quarter view of floor-standing FFU central control cabinet with blue touchscreen

FFU 및 터미널 공기 정화 장비

FFU 중앙 제어 시스템

A floor-standing control cabinet that supervises multiple FFU zones through an industrial HMI, protected power distribution and building-network communication.

Multi-Zone HMI Control
Central Alarm Overview
Operating Data Logging
BACnet or Modbus Interface

견적 요청 제품 찾아보기

상품 소개

The FFU central control system consolidates cleanroom fan commands, feedback and alarms in a lockable electrical cabinet. An industrial touchscreen presents zone status, airflow or speed setpoints and maintenance warnings, while internal PLC, power supplies, circuit protection and network repeaters distribute commands to field-connected EC fan filter units. The architecture can place routine room operation on the HMI and pass selected points to the building management system. Separate power and communication terminals simplify commissioning and isolate a field wiring fault from the supervisory electronics.

주요 기능

A graphical HMI displays FFU zones, operating states and active faults from one service location.

PLC-based sequences can apply occupied, standby and recovery setpoints to different cleanroom areas.

Logged fan hours, alarm events and selected environmental points support maintenance planning.

Isolated BACnet or Modbus communication exchanges approved status and command points with the BMS.

고객 제품 관심사

A large FFU installation becomes difficult to operate when individual units lack common setpoints, fault visibility and a controlled interface to the building system.

Operators walk through multiple rooms to change hundreds of local fan settings.The central HMI applies commands to defined FFU zones from one supervised interface.

A failed fan remains unnoticed until particle control is affected.Motor feedback and communication alarms identify the affected address and zone promptly.

Night operation consumes full fan power even when contamination loads are low.Scheduled occupied and standby modes reduce selected EC fan setpoints without shutting down monitoring.

Direct BMS commands can conflict with local cleanroom operating sequences.A defined gateway exposes selected points while the PLC retains interlocks and command priorities.

일반적인 응용 프로그램

Large semiconductor FFU ceilingsMulti-room pharmaceutical facilitiesBattery dry-room clean zonesDisplay and optics manufacturingCentral cleanroom operations centres

기술 매개변수

Representative enclosure and electronics ranges for an FFU central control system are listed below.

핵심 재료	Industrial PLC, touchscreen HMI, 24 VDC power supplies, protected distribution and isolated RS-485/Ethernet gateways
패널 두께	180-300 mm control-cabinet depth
유효 폭	600-1000 mm nominal cabinet width
최대 길이	Up to 1800 mm cabinet height for expanded power and communication sections
강철 면면 두께	1.5-2.0 mm powder-coated steel enclosure and hinged front door
코어 밀도	Approximately 1800-1900 kg/m³ nominal density of the FR-4 substrate used in the central control board
열전도도 (Thermal Conductivity)	Approximately 0.25-0.40 W/(m·K) through the FR-4 substrate inside the FFU central controller
표면 마무리	Light-grey or cleanroom-white epoxy-polyester powder-coated cabinet with sealed HMI bezel
접합 유형	Gasketed hinged door, DIN-rail terminal blocks, separated gland plates and pluggable field connectors
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Wall-mount or floor-standing cabinetBACnet MS/TP, Modbus RTU or Ethernet gatewayDifferential pressure and temperature inputsRemote web dashboard and event logging

Planning a FFU Central Control System specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.