English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
مرشحات الهواء والترشيح الكيميائي
E مكافئ الضغط مرشح لقط الجمعية
A stainless swing-bolt and bearing-bar mechanism that applies balanced compression to a filter gasket while moving clear for element removal.
- Uniform Gasket Compression
- Swing-Clear Service
- Tool-Controlled Adjustment
- Stainless Hardware
مقدمة المنتج
This assembly secures box-style HEPA, ULPA or compact filters against a flat sealing flange. Threaded swing bolts pull a rigid equal-bearing bar toward the frame so the load is spread along the filter edge rather than concentrated at isolated clips. Captive pivots keep components attached during maintenance, and the bar swings or slides away from the opening when loosened. Stainless construction suits repeated use in clean and corrosive air systems.
الخصائص الرئيسية
Threaded adjustment accommodates small differences in gasket and frame depth.
Captive pivots prevent loose hardware from falling into the air system.
The assembly moves outside the filter envelope for unrestricted removal.
مخاوف المنتج للعملاء
Uneven or improvised clamps can over-compress one gasket corner while leaving another side open to bypass.
Point clips leave low-pressure areas along a long filter edge.A rigid bearing bar distributes load over a wider sealing line.
Clamp parts are lost during overhead filter replacement.Captive bolts and pivots remain attached to the holding frame.
Different filter depths require new retaining hardware.Threaded travel allows the assembly to suit a defined range of frame and gasket heights.
The clamp blocks the filter as technicians pull it forward.Swing-clear geometry opens the complete removal path after release.
تطبيقات نموذجية
Gasket-seal HEPA holding framesSide-access filter housingsBuilt-up absolute filter banksCleanroom terminal boxesIndustrial compact-filter racks
المعلمات الفنية
Typical material and dimensional ranges for an equal-pressure filter clamp are shown below.
| المواد الأساسية | 304 stainless-steel swing bolts, pivots, equal-bearing bar and captive fasteners |
|---|---|
| سمك اللوحة | 2.0–4.0 mm formed bearing bar and mounting plates |
| العرض الفعال | 150–610 mm bearing length per filter edge |
| الحد الأقصى الطول | Up to 650 mm overall clamp assembly length |
| الصلب يواجه سمك | 2.0–4.0 mm stainless bearing and bracket components |
| الكثافة الأساسية | Approximately 8000 kg/m³ for 304 stainless-steel parts |
| الموصلية الحرارية | Approximately 14–17 W/(m·K) for passivated stainless clamp hardware |
| إنهاء السطح | Passivated stainless steel with smooth deburred edges |
| نوع المشترك | Captive swing-bolt pivot with threaded compression adjustment and equal-bearing retainer |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Single- or dual-bolt bearing barHand knob or tool-operated nutFrame-mounted or housing-mounted bracketAlternate travel for different filter depths
Planning a Equal-Pressure Filter Clamping Assembly specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
