English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أبواب الغرف النظيفة ونوافذ وأنظمة التشابك
غرفة نظيفة باب موقف الاستشعار
A matched magnetic contact set that reports whether a cleanroom door leaf is physically aligned with the closed frame position.
- Non-Contact Magnetic Sensing
- Sealed Reed Contact
- Dry-Contact Controller Output
- Interlock Feedback
مقدمة المنتج
The cleanroom door position sensor pairs a reed-switch module on the frame with a permanent magnet on the moving leaf. When the door closes and the two housings align within the sensing gap, the magnetic field changes the dry contact state sent to the interlock or access controller. Stainless or smooth white housings protect the encapsulated components, and the absence of a mechanical plunger removes a contact point from the clean opening.
الخصائص الرئيسية
Encapsulated reed contacts resist contamination at the sensing element and require no exposed actuator.
Separate sensor and magnet housings accommodate frame-to-leaf movement across a controlled gap.
Dry-contact wiring integrates with interlocks, access panels and local door-status indicators.
مخاوف المنتج للعملاء
The control system must distinguish a physically closed door from one that is merely locked or moving through the frame.
A mechanical limit switch wears or traps residue where its plunger touches the door.The sealed reed and magnet sense alignment without mechanical contact.
Frame movement causes intermittent feedback when the sensing gap is too narrow.Matched surface or recessed housings provide a defined operating gap and adjustment range.
An interlock releases the opposite door before the first leaf has fully returned.The controller receives a dedicated closed-position contact from the aligned sensor pair.
تطبيقات نموذجية
Cleanroom interlock feedbackAccess-controlled laboratory doorsAutomatic door closed-position inputPersonnel and material airlocks
المعلمات الفنية
Typical dimensions and material data for a sealed cleanroom magnetic door contact are listed below.
| المواد الأساسية | Hermetically sealed reed capsule with copper-alloy contacts and ferrite permanent magnet |
|---|---|
| سمك اللوحة | Approximately 12–25 mm housing depth |
| العرض الفعال | Approximately 19–38 mm module width |
| الحد الأقصى الطول | Approximately 110 mm for a long-range stainless sensor module |
| الصلب يواجه سمك | 0.8–1.2 mm brushed stainless-steel housing where selected |
| الكثافة الأساسية | Approximately 4800–5100 kg/m³ for the ferrite magnet core |
| الموصلية الحرارية | Approximately 3–5 W/(m·K) for the ferrite magnet material |
| إنهاء السطح | Brushed stainless steel or smooth white moulded polymer housing |
| نوع المشترك | Matched surface or recessed sensor-and-magnet pair aligned across a controlled gap |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Normally open, normally closed or changeover contactWhite polymer or stainless housingSurface or recessed mountingPrewired lead or screw-terminal connection
Planning a Cleanroom Door Position Sensor specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
