English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
معدات تهوية وتكييف ومعالجة الهواء في الغرف النظيفة
مضخة تعميم المياه المبردة
A base-mounted end-suction centrifugal pump that circulates chilled water between the chiller, air-handling coils and process cooling branches.
- Stable Hydronic Flow
- Back-Pull-Out Service
- Variable-Speed Ready
- Rigid Base Alignment
مقدمة المنتج
The chilled-water pump couples a single-stage cast-iron volute to a high-efficiency motor on a common baseplate. Its end-suction geometry provides a straight inlet path, while the top discharge fits conventional mechanical-room headers. A guarded flexible coupling accommodates minor alignment tolerance and allows the rotating assembly to be serviced without disturbing connected pipework when a back-pull-out arrangement is selected.
الخصائص الرئيسية
Common-base motor and pump alignment reduces vibration transmitted to cleanroom piping networks.
Mechanical-seal and coupling access supports planned maintenance without cutting the main suction and discharge lines.
Variable-frequency drive compatibility follows two-way valve demand and reduces unnecessary throttling energy.
مخاوف المنتج للعملاء
Chilled-water service requires correct flow, low vibration and reliable seals across continuously changing cooling demand.
Oversized constant-speed pumps waste energy against throttled valves.A variable-speed motor adjusts differential pressure and flow to actual coil demand.
Poor suction conditions create cavitation noise and impeller damage.A straight end-suction inlet and correctly selected NPSH margin support stable flow into the eye.
Motor-pump misalignment shortens bearing and seal life.A machined common base and guarded flexible coupling preserve shaft alignment.
Seal replacement causes extended system shutdown.Back-pull-out access removes the rotating assembly while the volute remains connected to the piping.
تطبيقات نموذجية
Primary chilled-water loopsSecondary variable-flow distributionCleanroom AHU coil circuitsProcess-equipment cooling waterLow-temperature laboratory systems
المعلمات الفنية
Typical mechanical construction for a cleanroom chilled-water pump set is summarized below.
| المواد الأساسية | Cast-iron volute with stainless steel or bronze impeller and steel shaft |
|---|---|
| سمك اللوحة | 8-16 mm fabricated steel baseplate thickness |
| العرض الفعال | 350-900 mm typical pump-set width |
| الحد الأقصى الطول | Up to 2400 mm including motor and coupling |
| الصلب يواجه سمك | 1.5-2.5 mm removable coupling-guard sheet |
| الكثافة الأساسية | Approximately 7000-7300 kg/m³ for cast-iron volute material |
| الموصلية الحرارية | Approximately 45-55 W/(m·K) for cast-iron wetted casing |
| إنهاء السطح | Blue epoxy coating on cast iron with painted steel base |
| نوع المشترك | Flanged suction/discharge, flexible shaft coupling and bolted base mounts |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Stainless steel or bronze impellerMechanical-seal material combinationsVariable-frequency drive and differential-pressure sensorSingle duty, duty-standby or twin-pump skid
Planning a Chilled-Water Circulation Pump specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
