İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda HVAC ve Hava İşleme Ekipmanları
Sıcak su yeniden ısınma bobinleri
A shallow one- or two-row hydronic coil that restores neutral supply-air temperature after deep cooling and dehumidification.
- Post-Dehumidification Reheat
- Shallow Low-Pressure-Drop Face
- Fast Valve Response
- Compact AHU Integration
Ürün tanıtımı
The reheat coil is positioned downstream of a cooling coil so it can add sensible heat without increasing air moisture. Its shallow copper-tube and aluminum-fin construction minimizes air pressure drop while providing enough surface area for precise leaving-temperature control. Low water volume and short circuits respond quickly to a modulating valve, making the coil suitable for tight cleanroom temperature and humidity sequences.
Ana Özellikler
Small internal water volume responds rapidly when the modulating valve changes position.
Accessible vents and drains prevent air binding during low-flow operation.
Compact casing fits between cooling-coil, fan and final-filter sections in constrained AHUs.
Müşteri Ürün Sorunları
Reheat must correct overcooled supply air precisely without adding excessive pressure drop or fighting the cooling sequence.
Air leaves the dehumidifying coil too cold for the occupied zone.A downstream hydronic coil adds only sensible heat and preserves the achieved moisture content.
An oversized multi-row coil causes sluggish temperature control.A shallow low-volume circuit responds quickly to modulating water flow.
Excessive fin resistance increases cleanroom fan power.A one- or two-row face and appropriate fin pitch minimize air-side pressure drop.
Simultaneous cooling and reheat waste plant energy.Heat-recovery or low-temperature return water can supply the reheat duty when available.
Tipik uygulamalar
Cleanroom temperature-humidity decouplingLaboratory dehumidification reheatHospital operating-room AHUsPharmaceutical make-up air unitsNeutral-temperature supply-air systems
Teknik parametreler
Typical physical ranges for a compact AHU hot-water reheat coil are summarized below.
| Temel malzemeler | Copper tubes with aluminum fins and compact copper headers |
|---|---|
| Panel kalınlığı | 1.2-1.8 mm galvanized steel casing |
| Effective Width (Etkili Genişlik) | 250-2200 mm active fin face width |
| Maksimum uzunluk | Up to 3200 mm overall casing length |
| Çelik yüz yüze kalınlığı | 1.2-1.8 mm galvanized or stainless frame |
| Core Density (Çekirdek Yoğunluğu) | Approximately 2730 kg/m³ for the thin 3003 aluminum fin stock in the shallow reheat section |
| Termal İletkenlik | Approximately 193 W/(m·K) for the 3003 aluminum reheat fins at room temperature |
| Yüzey bitirme | Natural or coated aluminum fins with bright galvanized casing |
| Ortak tip | Brazed copper tube/header joints inside a shallow flanged casing |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
One- or two-row circuitHeat-recovery, boiler-water or heat-pump-water serviceDifferent fin pitch and protective coatingsStainless casing with vent, drain and sensor pocket
Planning a Hot-Water Reheat Coil specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
