High-pressure mist humidifier pump station with nozzle manifold

Temiz Oda HVAC ve Hava İşleme Ekipmanları

Yüksek basınçlı sis nemlendirici

A high-capacity adiabatic system that pressurizes treated water and atomizes it through precision anti-drip nozzles into an AHU or large controlled space.

Fine High-Pressure Atomization
Low-Energy Adiabatic Operation
Anti-Drip Nozzle Manifold
Integrated Water Treatment

Alıntı isteği Browse ürünleri

Ürün tanıtımı

A stainless multistage pump raises treated water to high pressure and supplies a manifold of precision nozzles. Each orifice creates a fine mist that evaporates into the airstream, adding moisture while absorbing sensible heat. Filtration and reverse-osmosis pretreatment limit nozzle deposits, and staged nozzle banks or variable pump control match output to demand.

Ana Özellikler

High pressure forms small droplets with a high surface area for rapid adiabatic evaporation.

Stainless pump, tubing and manifold resist continuous purified-water service.

Anti-drip nozzles close positively when pressure falls and reduce post-cycle wetting.

Integrated filtration and treatment protect small orifices from scale and suspended particles.

Müşteri Ürün Sorunları

High-pressure systems require fine atomization, clean water and controlled staging so droplets evaporate before reaching surfaces.

Nozzle deposits change spray pattern and create large droplets.Fine filtration and low-mineral treated water protect the precision orifices.

Nozzles drip after the pump stops.Spring-loaded anti-drip valves close each nozzle below operating pressure.

Short duct length does not allow full mist absorption.Nozzle placement, droplet size and staged capacity are matched to airflow and available distance.

A fixed-output pump causes repeated on-off cycling.Variable-speed pressure control or staged nozzle zones follow the actual humidity demand.

Tipik uygulamalar

Large pharmaceutical cleanroomsElectronics manufacturing hallsData-center air handlersPrinting and paper productionIndustrial evaporative cooling and humidification

Teknik parametreler

Representative construction ranges for a packaged high-pressure mist station are listed below.

Temel malzemeler	AISI 304 or 316 stainless pump, manifold and tubing with ceramic or stainless nozzles
Panel kalınlığı	1.2-2.0 mm powder-coated control-cabinet panels
Effective Width (Etkili Genişlik)	600-1800 mm packaged pump-station width
Maksimum uzunluk	Up to 5000 mm modular nozzle-manifold section length
Çelik yüz yüze kalınlığı	1.2-2.0 mm cabinet and stainless base sheet
Core Density (Çekirdek Yoğunluğu)	Approximately 7900-8000 kg/m³ for stainless pump, manifold and tubing material
Termal İletkenlik	Approximately 14-16 W/(m·K) for stainless water-contact parts
Yüzey bitirme	White-blue powder coating with passivated stainless pump and tubing
Ortak tip	Compression-connected high-pressure tubing with threaded anti-drip nozzles and bolted skid
Customization (Özelleşme)	Kullanılan uygulama ve çalışma ortamına göre kullanılabilir.

Mevcut Seçenekler

In-duct or direct-room nozzle arrangementIntegrated reverse-osmosis and ultraviolet treatmentVariable-speed pump or staged solenoid zonesStainless droplet separator and water-quality monitoring

Planning a High-Pressure Mist Humidifier specification?

Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.

Ekibimizle konuşun