İngilizce
Almanca
Arapça
Fransızca
Endonezya dilinde
Japonca
Korece
Malay dilinde
Portekizce
Rusça
İspanyolca
Taylandca
TürkçeCurrent
Vietnamca
Temiz Oda Ekipmanları Yedek Parçaları
FFU Gel Seal
A refillable fluid-gel trough that forms a conformable low-bypass seal around an FFU HEPA filter knife-edge interface.
- Continuous Fluid-Gel Barrier
- Knife-Edge Interface
- Refillable Aluminum Trough
- Conformable Low-Bypass Seal
Ürün tanıtımı
The FFU gel seal uses a continuous channel of stable silicone gel to receive the projecting knife edge of a mating HEPA filter or housing. As the knife edge enters the gel, the fluid conforms around minor dimensional variation without the compression load required by a foam gasket. An aluminum trough retains the gel around the full perimeter, with sealed corners and an optional fill port for controlled service. Trough dimensions, gel depth, viscosity and knife-edge immersion must match the installed filter system.
Ana Özellikler
A rigid aluminum trough controls gel depth and prevents migration from the sealing path.
Mitered or welded corner construction maintains channel continuity at perimeter turns.
A capped fill port supports controlled topping-up or replacement of compatible gel.
Müşteri Ürün Sorunları
A fluid seal only performs reliably when the trough remains continuous and the mating knife edge reaches the correct gel depth.
Insufficient gel depth leaves sections of the knife edge unsealed.Trough volume and fill level are matched to the knife-edge height and intended immersion.
Corner discontinuities become bypass paths around an otherwise sealed perimeter.Sealed corner joints maintain one uninterrupted gel channel around the frame.
Incompatible gel hardens, flows or contaminates the mating surface.Gel chemistry and consistency are selected for the operating temperature and filter interface materials.
Overfilling causes gel displacement during filter installation.A defined trough profile and controlled refill quantity keep the gel below its retention lips.
Tipik uygulamalar
Gel-seal FFU HEPA interfacesCleanroom terminal filter housingsPharmaceutical ceiling filter modulesLow-bypass filter replacement systems
Teknik parametreler
Typical construction ranges for FFU fluid-gel seal troughs are shown below.
| Temel malzemeler | Non-curing silicone sealing gel retained in an aluminum perimeter trough |
|---|---|
| Panel kalınlığı | 15-40 mm nominal trough depth |
| Effective Width (Etkili Genişlik) | 300-610 mm nominal frame width |
| Maksimum uzunluk | Up to 1220 mm nominal frame length |
| Çelik yüz yüze kalınlığı | 0.8-1.5 mm optional stainless-steel cover or retaining component |
| Core Density (Çekirdek Yoğunluğu) | Approximately 950-1050 kg/m³ for the silicone gel |
| Termal İletkenlik | Approximately 0.15-0.25 W/(m·K) for silicone sealing gel |
| Yüzey bitirme | Natural silver aluminum trough with translucent blue or clear silicone gel |
| Ortak tip | Continuous U-channel trough with sealed mitered corners and optional capped fill port |
| Customization (Özelleşme) | Kullanılan uygulama ve çalışma ortamına göre kullanılabilir. |
Mevcut Seçenekler
Blue or clear compatible gelCustom trough dimensionsCapped fill and drain portsMatched knife-edge immersion depth
Planning a FFU Gel Seal specification?
Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.
