Inglês
Alemão
Língua árabe
Francês
Língua indonésia
Japonês
Coreano
Língua malaia
Portuguêsatual
Língua russa
Espanhol
Tailandês
Língua turca
Vietnã
Filtros de ar e filtragem química
Filtro HEPA Seal
A rigid HEPA panel fitted with a closed-cell perimeter gasket that seals against a flat housing flange under controlled compression.
- Closed-Cell Compression Gasket
- Flat-Flange Compatibility
- Simple Visual Inspection
- Replaceable Seal Option
Introdução do produto
The gasket-seal HEPA filter uses a flat closed-cell neoprene, EPDM or polyurethane gasket bonded to the upstream or downstream flange of an anodized-aluminum, galvanized or wood cell. Retaining clips or a clamping mechanism compress the gasket uniformly against the housing's flat sealing face. The mini-pleat or separator-style HEPA pack is potted independently into the cell, while dovetailed or continuously poured gasket corners prevent leakage at the perimeter joints. This familiar dry-seal arrangement suits built-up banks and terminal frames with accessible, flat mating surfaces.
Características-chave
A broad flat gasket face is easy to inspect for dirt, tears and incomplete contact before installation.
Dovetailed or seamless corners maintain continuity around the complete perimeter.
Upstream and downstream gasket positions accommodate different filter-bank loading directions.
Preocupações do produto do cliente
Dry gasket seals depend on clean mating surfaces and uniform compression around every side of the filter frame.
Uneven clamp force leaves one corner of the filter unsealed.A resilient full-width gasket and distributed retaining points maintain perimeter compression.
Open-cell foam allows leakage through the gasket body.Closed-cell neoprene, EPDM or polyurethane provides a low-permeability compression barrier.
Butt-jointed gasket corners separate during filter handling.Dovetailed interlocking corners or a continuously poured gasket remove straight-through corner gaps.
Repeated replacement leaves adhesive residue and a distorted seal face.A replaceable preformed gasket and clean flat flange simplify inspection and renewal.
Aplicações típicas
Built-up HEPA filter banksFront-access air-handling unitsCleanroom terminal housingsHospital and laboratory ventilationPharmaceutical supply and return systems
Parâmetros técnicos
Typical construction ranges for a compression gasket-seal HEPA filter are listed below.
| Material principal | Mini-pleated microglass or membrane HEPA media; separator pack available for full-depth cells |
|---|---|
| Painel de espessura | 70-120 mm mini-pleat panel or 150-292 mm separator cell depth |
| Largura efetiva | 305-610 mm modular face width |
| Comprimento máximo | Up to 1220 mm for reinforced mini-pleat panels |
| Aço enfrentando espessura | 0.40-0.80 mm galvanized or stainless-steel protective faceguard |
| Densidade Core | Approximately 85-155 kg/m³ nominal assembled media-pack density |
| Condutividade térmica | Approximately 0.034-0.041 W/(m·K) for dry gasketed microglass filter media |
| Superfície acabado | Anodized aluminum, galvanized steel or sealed wood with black or white closed-cell gasket |
| Tipo conjunto | Closed-cell perimeter gasket compressed against a clean flat housing flange |
| Customização | Disponível com base na aplicação pretendida e no ambiente operacional. |
Opções disponíveis
H13, H14 or 99.97-99.999% at 0.3 µmNeoprene, EPDM or polyurethane gasketUpstream, downstream or dual-face gasketDovetailed preformed or seamless poured corners
Planning a Gasket-Seal HEPA Filter specification?
Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.
