Bahasa Inggeris
Bahasa Jerman
Bahasa Arab (Bahasa Melayu)
Bahasa Perancis
Bahasa Indonesia: Bahasa Indonesia
Bahasa Jepun
Bahasa Korea (Bahasa Melayu)
Bahasa Melayu (Bahasa Melayu)Semasa
Bahasa Portugis: Bahasa Portugis: Bahasa Portugis
Bahasa Rusia
Bahasa Sepanyol: Bahasa Sepanyol: Bahasa Sepanyol
Bahasa Melayu (Bahasa Melayu)
Bahasa Turki: Bahasa Turki
Bahasa Vietnam (Bahasa Melayu)
Penapis udara dan penapisan kimia
Penapis HEPA Gasket-Seal
A rigid HEPA panel fitted with a closed-cell perimeter gasket that seals against a flat housing flange under controlled compression.
- Closed-Cell Compression Gasket
- Flat-Flange Compatibility
- Simple Visual Inspection
- Replaceable Seal Option
Pengenalan Produk
The gasket-seal HEPA filter uses a flat closed-cell neoprene, EPDM or polyurethane gasket bonded to the upstream or downstream flange of an anodized-aluminum, galvanized or wood cell. Retaining clips or a clamping mechanism compress the gasket uniformly against the housing's flat sealing face. The mini-pleat or separator-style HEPA pack is potted independently into the cell, while dovetailed or continuously poured gasket corners prevent leakage at the perimeter joints. This familiar dry-seal arrangement suits built-up banks and terminal frames with accessible, flat mating surfaces.
Ciri-ciri Utama
A broad flat gasket face is easy to inspect for dirt, tears and incomplete contact before installation.
Dovetailed or seamless corners maintain continuity around the complete perimeter.
Upstream and downstream gasket positions accommodate different filter-bank loading directions.
Kebimbangan Produk Pelanggan
Dry gasket seals depend on clean mating surfaces and uniform compression around every side of the filter frame.
Uneven clamp force leaves one corner of the filter unsealed.A resilient full-width gasket and distributed retaining points maintain perimeter compression.
Open-cell foam allows leakage through the gasket body.Closed-cell neoprene, EPDM or polyurethane provides a low-permeability compression barrier.
Butt-jointed gasket corners separate during filter handling.Dovetailed interlocking corners or a continuously poured gasket remove straight-through corner gaps.
Repeated replacement leaves adhesive residue and a distorted seal face.A replaceable preformed gasket and clean flat flange simplify inspection and renewal.
Permohonan yang biasa
Built-up HEPA filter banksFront-access air-handling unitsCleanroom terminal housingsHospital and laboratory ventilationPharmaceutical supply and return systems
Parameter teknikal
Typical construction ranges for a compression gasket-seal HEPA filter are listed below.
| Bahan Teras | Mini-pleated microglass or membrane HEPA media; separator pack available for full-depth cells |
|---|---|
| Ketebalan Panel | 70-120 mm mini-pleat panel or 150-292 mm separator cell depth |
| Lebar berkesan | 305-610 mm modular face width |
| Panjang maksimum | Up to 1220 mm for reinforced mini-pleat panels |
| Keluli Menghadapi Ketebalan | 0.40-0.80 mm galvanized or stainless-steel protective faceguard |
| Ketumpatan teras | Approximately 85-155 kg/m³ nominal assembled media-pack density |
| Kekonduksian Terma | Approximately 0.034-0.041 W/(m·K) for dry gasketed microglass filter media |
| Kemasan permukaan | Anodized aluminum, galvanized steel or sealed wood with black or white closed-cell gasket |
| Jenis Bersatu | Closed-cell perimeter gasket compressed against a clean flat housing flange |
| Penyesuaian | Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi. |
Pilihan yang boleh didapati
H13, H14 or 99.97-99.999% at 0.3 µmNeoprene, EPDM or polyurethane gasketUpstream, downstream or dual-face gasketDovetailed preformed or seamless poured corners
Planning a Gasket-Seal HEPA Filter specification?
Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.
