Inglês
Alemão
Língua árabe
Francês
Língua indonésia
Japonês
Coreano
Língua malaia
Portuguêsatual
Língua russa
Espanhol
Tailandês
Língua turca
Vietnã
Equipamento de sala limpa Peças de reposição
AHU Fan Belt
A fabric-wrapped classical V-belt for restoring matched torque transmission between an AHU fan motor pulley and blower sheave.
- Wrapped V Profile
- Reinforced Tension Cords
- Matched Pulley Contact
- HVAC Drive Replacement
Introdução do produto
The AHU fan belt is an endless trapezoidal power-transmission belt used between the motor pulley and fan shaft sheave of a belt-driven air-handling unit. A resilient elastomer body transfers load through the pulley groove, longitudinal tension cords control stretch, and a fabric wrap protects the working surfaces from abrasion. Correct replacement depends on profile, datum or pitch length, matched-set tolerance, pulley condition and installation tension. A new belt should not be forced over a sheave and multiple-belt drives require a length-matched set rather than a mixture of new and worn belts.
Características-chave
Longitudinal tensile cords limit elongation while repeatedly flexing around the motor and fan sheaves.
The wrapped fabric cover protects the belt flanks and outer surface against handling wear and repeated groove contact.
A continuous molded body avoids mechanical joints and supports even load transfer around the entire belt circumference.
Preocupações do produto do cliente
Fan-drive reliability depends on selecting the exact section and effective length, then installing it on aligned pulleys at the specified tension.
A belt with the wrong cross-section rides too high or too low in the pulley groove and cannot transmit load correctly.Top width, section height and groove profile are matched to the existing sheaves before the replacement is supplied.
An incorrect effective length can leave too little adjustment for proper tension or overload the shaft bearings.The existing belt designation and measured drive geometry are used to select the appropriate datum or pitch length.
Replacing only one belt in a multi-groove drive causes unequal load sharing between old and new belts.Parallel drives are serviced with a factory-matched set of equal-length belts installed at the same time.
Pulley misalignment and excessive pretension accelerate flank wear, heat generation and vibration.The belt is paired with inspected, aligned sheaves and tensioned by the AHU maintenance procedure rather than levered into place.
Aplicações típicas
Belt-driven AHU supply fansReturn-air blower drivesCleanroom exhaust fan sectionsVentilation equipment replacement maintenance
Parâmetros técnicos
Typical material construction and dimensional ranges for wrapped classical AHU fan V-belts are listed below.
| Material principal | Synthetic-rubber compression body with polyester tension cords and woven fabric wrap |
|---|---|
| Painel de espessura | 6-32 mm nominal belt section height, depending on profile |
| Largura efetiva | 10-40 mm nominal top width, depending on classical V-belt section |
| Comprimento máximo | Up to 5000 mm nominal datum length for common AHU drive selections |
| Aço enfrentando espessura | 0 mm; nonmetallic wrapped belt construction |
| Densidade Core | Approximately 1100-1300 kg/m³ for reinforced rubber composite |
| Condutividade térmica | Approximately 0.15-0.25 W/(m·K) for the rubber-fabric composite |
| Superfície acabado | Matte black friction-resistant woven fabric wrap over all external belt faces |
| Tipo conjunto | Continuous molded endless loop with trapezoidal sidewalls for V-grooved pulleys |
| Customização | Disponível com base na aplicação pretendida e no ambiente operacional. |
Opções disponíveis
Classical Z, A, B, C or D profileMatched multi-belt setAlternative effective lengthWrapped or raw-edge construction
Planning a AHU Fan Belt specification?
Envie-nos as suas dimensões, condições de instalação, metas de desempenho e acabamento de superfície necessário.
