English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
ملابس الغرف النظيفة، PPE والمواد الاستهلاكية
حصيرة لاصقة
Multilayer cleanroom sticky mat with peel-away polyethylene sheets, water-based acrylic tack and numbered corner tabs for routine contamination control.
- Peel-away adhesive layers for controlled entrances
- Captures particles from footwear and cart wheels
- Low-profile polyethylene construction with numbered tabs
مقدمة المنتج
This Sticky Mat provides a simple floor-level barrier at gowning rooms, airlocks and controlled-area entrances. Each thin polyethylene sheet carries a uniform water-based acrylic adhesive that lifts loose dust from shoe soles, boot covers, casters and cart wheels. When the exposed surface becomes loaded, the operator removes one numbered layer to reveal a fresh tacky sheet without moving the base mat.
الخصائص الرئيسية
Numbered corner tabs make remaining-layer checks straightforward
Uniform low-tack surface captures debris without excessive shoe pull
Smooth film supports repeated personnel and light-cart traffic
Floor-side adhesive or an optional frame keeps edges stable in use
مخاوف المنتج للعملاء
Entrance contamination control must balance particle pickup, safe passage and predictable maintenance. The mat should remain flat, release footwear cleanly and allow a soiled layer to be removed without spreading captured debris.
Excessive tack may pull at boot covers or create an uncomfortable step.Select medium or high tack according to footwear, wheel load and operating procedure.
Weak edge adhesion can allow the mat to curl under cart traffic.Apply the mat to a clean, dry floor or use a compatible rigid mat frame.
Staff may replace the entire mat before all usable layers are consumed.Use clearly numbered peel tabs to identify the active sheet and remaining stock.
Removing a dirty sheet may transfer captured particles to the floor.Peel the loaded layer slowly toward the center and dispose of it immediately in the designated waste stream.
تطبيقات نموذجية
Used at cleanroom and laboratory entrances, gowning-room transition points, airlocks, packaging areas, electronics assembly zones and cart-transfer routes where footwear and wheel-borne particles must be reduced.
المعلمات الفنية
The following values describe common peel-off cleanroom sticky-mat constructions. Final dimensions, color, tack grade and packaging can be selected for the entrance layout and traffic pattern.
| المواد الأساسية | Multilayer low-density polyethylene film with water-based acrylic adhesive |
|---|---|
| سمك اللوحة | 1.5-2.0 mm for a typical 30-layer mat |
| العرض الفعال | 450-900 mm |
| الحد الأقصى الطول | 1500 mm |
| الصلب يواجه سمك | 0 mm; no steel facing used |
| الكثافة الأساسية | 910-940 kg/m³ polyethylene film |
| الموصلية الحرارية | 0.33-0.50 W/(m·K), material dependent |
| إنهاء السطح | Smooth blue or white peel-away adhesive film with numbered corner tabs |
| نوع المشترك | Laminated peel-off sheet stack with floor-side adhesive backing |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Blue, white, clear or grey filmMedium-tack or high-tack surface30-sheet or 60-sheet stacksFull adhesive backing or adhesive stripsNumbered removable corner tabsCompatible rigid or flexible mat frame
Planning a Sticky Mat specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
