English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة الجدار والسقف للغرفة النظيفة
الفولاذ المقاوم للصدأ غرف الأبحاث تحطم السكك الحديدية
A wall-mounted 304 or 316L stainless steel rail that intercepts carts and mobile equipment before they damage cleanroom panels, glazing or built-in services.
- Heavy-Duty Wall Protection
- Concealed Rear Brackets
- 304 or 316L Stainless Steel
- Rounded Cleanable Edges
مقدمة المنتج
Stainless Steel Cleanroom Crash Rails create a continuous impact line along busy cleanroom corridors and material routes. A thick flat bar or formed rail is spaced from the wall on welded rear studs and Z-brackets, allowing trolley frames and carts to contact the guard before reaching the finished panel. Concealed front fixings leave a smooth exposed surface, and rounded or fully welded ends remove sharp edges. Standard 304 stainless steel covers most dry interiors; 316L and alternative polishing are available for higher chemical or wash-down exposure.
الخصائص الرئيسية
Rear-mounted brackets eliminate exposed fastener heads from the impact face.
The wall offset can clear coving, service panels and minor surface projections.
Rounded ends and smooth welds avoid sharp corners along pedestrian routes.
Modular rail lengths can be joined around corridors while maintaining a consistent protection height.
مخاوف المنتج للعملاء
A crash rail must protect the wall at the correct impact height, transfer loads into sound supports and remain accessible for cleaning behind the rail.
Cart frames strike the wall above low skirting and dent cleanroom panels.The rail is mounted at the actual equipment contact height to intercept horizontal movement.
Weak surface fixings pull out of thin panel skins under repeated contact.Rear brackets align with internal reinforcement or independent wall support points.
A rail mounted too close to the wall leaves no room to wipe behind it.A controlled stand-off creates cleaning access without projecting unnecessarily into the corridor.
Open tube ends and rough welds become contamination traps.Closed rounded ends and dressed welds keep the guard smooth and fully cleanable.
تطبيقات نموذجية
Cleanroom material corridorsPharmaceutical warehouse interfacesHospital sterile supply routesFood-production trolley lanesLaboratory equipment movement areas
المعلمات الفنية
Typical stainless steel cleanroom crash-rail dimensions are shown below.
| المواد الأساسية | Solid AISI 304 stainless steel; 316L optional |
|---|---|
| سمك اللوحة | 6 mm flat-bar thickness |
| العرض الفعال | 76, 102 or 152 mm rail height |
| الحد الأقصى الطول | 3000 mm per section |
| الصلب يواجه سمك | 6 mm stainless steel rail |
| الكثافة الأساسية | N/A — solid stainless steel construction |
| الموصلية الحرارية | N/A — wall protection component, not insulation |
| إنهاء السطح | ASTM No. 4 or 320-grit satin polished stainless steel |
| نوع المشترك | Rear welded studs on concealed Z-brackets with closed end caps |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
304 or 316L stainless steel76, 102 and 152 mm heights38–150 mm wall stand-offStraight, corner and returned-end sections
Planning a Stainless Steel Cleanroom Crash Rail specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
