English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة الأرضيات الغرف النظيفة
الكهربائية موصل PVC الأرضيات
A permanently conductive homogeneous PVC floor that transfers charge through the sheet, conductive adhesive and copper grounding network in ESD-controlled rooms.
- 5×10⁴–1×10⁶ Ω Resistance
- Permanent Conductive Matrix
- Copper-Strip Grounding
- Impervious Welded Seams
مقدمة المنتج
Electrostatic-conductive PVC flooring disperses conductive particles through a compact homogeneous sheet so charge has a continuous path from the walking surface to ground. The sheet is installed with an approved conductive adhesive and connected to copper strips or grounding points designed for the room. Welded joints retain a closed, cleanable surface without interrupting the electrical network. This low-resistance category is intended for areas where sensitive devices, powders or electronic processes require faster charge drainage than a general antistatic finish provides.
الخصائص الرئيسية
Typical resistance to ground of 5×10⁴–1×10⁶ Ω provides controlled charge drainage for designated ESD areas.
Conductive adhesive and copper tape connect individual sheets to the building grounding system.
Hot-welded seams maintain an impervious surface around equipment and cleaning routes.
مخاوف المنتج للعملاء
A conductive floor must drain charge predictably across the complete installed system rather than only at the visible sheet surface.
A decorative antistatic coating does not provide the low resistance required by sensitive electronics.Conductive particles extend through the homogeneous PVC body to support a 5×10⁴–1×10⁶ Ω system range.
Isolated conductive sheets have no dependable route to the building earth.Copper strips and conductive adhesive link the floor field to designated grounding points.
Floor seams become liquid and contamination paths after repeated cleaning.Routed hot-welded joints close the sheet edges while preserving the conductive installation below.
Humidity changes cause inconsistent static-control performance in unsuitable products.The selected flooring uses a permanent conductive matrix rather than moisture-dependent surface treatment.
تطبيقات نموذجية
Microelectronics cleanroomsSemiconductor assembly and test areasMedical electronics productionInstrument calibration laboratoriesESD-protected packaging rooms
المعلمات الفنية
Representative construction data for a homogeneous electrostatic-conductive PVC sheet system are provided below.
| المواد الأساسية | Homogeneous PVC compound with uniformly distributed conductive carbon and mineral particles |
|---|---|
| سمك اللوحة | 2.0 mm total conductive sheet thickness |
| العرض الفعال | 2000 mm standard sheet width |
| الحد الأقصى الطول | Up to 20000 mm standard roll length |
| الصلب يواجه سمك | 0 mm; the conductive vinyl sheet contains no steel facing |
| الكثافة الأساسية | Approximately 1750 kg/m³ based on a 3500 g/m² sheet at 2.0 mm thickness |
| الموصلية الحرارية | Approximately 0.25 W/(m·K) for compact conductive PVC |
| إنهاء السطح | Dense marbleized conductive surface suitable for approved ESD maintenance products |
| نوع المشترك | Hot-welded sheet seams over conductive adhesive with copper-strip grounding connections |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Sheet or modular conductive tile formatCopper-strip grounding layoutColor-matched hot-welding rodCoved wall transition and conductive adhesive system
Planning a Electrostatic-Conductive PVC Flooring specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
