Charcoal electrostatic-conductive PVC flooring roll with copper grounding strip

Sistem Lantai Bilik Bersih

Lantai PVC Elektrostatik-Konduktif

A permanently conductive homogeneous PVC floor that transfers charge through the sheet, conductive adhesive and copper grounding network in ESD-controlled rooms.

5×10⁴–1×10⁶ Ω Resistance
Permanent Conductive Matrix
Copper-Strip Grounding
Impervious Welded Seams

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

Electrostatic-conductive PVC flooring disperses conductive particles through a compact homogeneous sheet so charge has a continuous path from the walking surface to ground. The sheet is installed with an approved conductive adhesive and connected to copper strips or grounding points designed for the room. Welded joints retain a closed, cleanable surface without interrupting the electrical network. This low-resistance category is intended for areas where sensitive devices, powders or electronic processes require faster charge drainage than a general antistatic finish provides.

Ciri-ciri Utama

A conductive compound throughout the 2 mm sheet avoids dependence on a temporary surface polish for primary electrical performance.

Typical resistance to ground of 5×10⁴–1×10⁶ Ω provides controlled charge drainage for designated ESD areas.

Conductive adhesive and copper tape connect individual sheets to the building grounding system.

Hot-welded seams maintain an impervious surface around equipment and cleaning routes.

Kebimbangan Produk Pelanggan

A conductive floor must drain charge predictably across the complete installed system rather than only at the visible sheet surface.

A decorative antistatic coating does not provide the low resistance required by sensitive electronics.Conductive particles extend through the homogeneous PVC body to support a 5×10⁴–1×10⁶ Ω system range.

Isolated conductive sheets have no dependable route to the building earth.Copper strips and conductive adhesive link the floor field to designated grounding points.

Floor seams become liquid and contamination paths after repeated cleaning.Routed hot-welded joints close the sheet edges while preserving the conductive installation below.

Humidity changes cause inconsistent static-control performance in unsuitable products.The selected flooring uses a permanent conductive matrix rather than moisture-dependent surface treatment.

Permohonan yang biasa

Microelectronics cleanroomsSemiconductor assembly and test areasMedical electronics productionInstrument calibration laboratoriesESD-protected packaging rooms

Parameter teknikal

Representative construction data for a homogeneous electrostatic-conductive PVC sheet system are provided below.

Bahan Teras	Homogeneous PVC compound with uniformly distributed conductive carbon and mineral particles
Ketebalan Panel	2.0 mm total conductive sheet thickness
Lebar berkesan	2000 mm standard sheet width
Panjang maksimum	Up to 20000 mm standard roll length
Keluli Menghadapi Ketebalan	0 mm; the conductive vinyl sheet contains no steel facing
Ketumpatan teras	Approximately 1750 kg/m³ based on a 3500 g/m² sheet at 2.0 mm thickness
Kekonduksian Terma	Approximately 0.25 W/(m·K) for compact conductive PVC
Kemasan permukaan	Dense marbleized conductive surface suitable for approved ESD maintenance products
Jenis Bersatu	Hot-welded sheet seams over conductive adhesive with copper-strip grounding connections
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Sheet or modular conductive tile formatCopper-strip grounding layoutColor-matched hot-welding rodCoved wall transition and conductive adhesive system

Planning a Electrostatic-Conductive PVC Flooring specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami