Charcoal electrostatic-conductive PVC flooring roll with copper grounding strip

Cleanroom Flooring Sistem

Lantai PVC Elektrostatik-Konduktif

A permanently conductive homogeneous PVC floor that transfers charge through the sheet, conductive adhesive and copper grounding network in ESD-controlled rooms.

5×10⁴–1×10⁶ Ω Resistance
Permanent Conductive Matrix
Copper-Strip Grounding
Impervious Welded Seams

Permintaan untuk kutipan Browse Produk

Perkenalan produk

Electrostatic-conductive PVC flooring disperses conductive particles through a compact homogeneous sheet so charge has a continuous path from the walking surface to ground. The sheet is installed with an approved conductive adhesive and connected to copper strips or grounding points designed for the room. Welded joints retain a closed, cleanable surface without interrupting the electrical network. This low-resistance category is intended for areas where sensitive devices, powders or electronic processes require faster charge drainage than a general antistatic finish provides.

Fitur utama:

A conductive compound throughout the 2 mm sheet avoids dependence on a temporary surface polish for primary electrical performance.

Typical resistance to ground of 5×10⁴–1×10⁶ Ω provides controlled charge drainage for designated ESD areas.

Conductive adhesive and copper tape connect individual sheets to the building grounding system.

Hot-welded seams maintain an impervious surface around equipment and cleaning routes.

Kekhawatiran produk pelanggan

A conductive floor must drain charge predictably across the complete installed system rather than only at the visible sheet surface.

A decorative antistatic coating does not provide the low resistance required by sensitive electronics.Conductive particles extend through the homogeneous PVC body to support a 5×10⁴–1×10⁶ Ω system range.

Isolated conductive sheets have no dependable route to the building earth.Copper strips and conductive adhesive link the floor field to designated grounding points.

Floor seams become liquid and contamination paths after repeated cleaning.Routed hot-welded joints close the sheet edges while preserving the conductive installation below.

Humidity changes cause inconsistent static-control performance in unsuitable products.The selected flooring uses a permanent conductive matrix rather than moisture-dependent surface treatment.

Aplikasi yang Tipis

Microelectronics cleanroomsSemiconductor assembly and test areasMedical electronics productionInstrument calibration laboratoriesESD-protected packaging rooms

Parameter teknis

Representative construction data for a homogeneous electrostatic-conductive PVC sheet system are provided below.

Bahan inti	Homogeneous PVC compound with uniformly distributed conductive carbon and mineral particles
Ketebalan Panel (Panel Thickness)	2.0 mm total conductive sheet thickness
Efektif lebar	2000 mm standard sheet width
Panjang maksimum	Hingga 20000 mm panjang roll standar
Baja menghadap ketebalan	0 mm; the conductive vinyl sheet contains no steel facing
Kepadatan inti (core density)	Approximately 1750 kg/m³ based on a 3500 g/m² sheet at 2.0 mm thickness
Konduktivitas Termal (Thermal Conductivity)	Approximately 0.25 W/(m·K) for compact conductive PVC
Permukaan selesai	Dense marbleized conductive surface suitable for approved ESD maintenance products
Jenis Bersama	Hot-welded sheet seams over conductive adhesive with copper-strip grounding connections
Customization (Kustomisasi)	Tersedia berdasarkan aplikasi yang dimaksudkan dan lingkungan operasi.

Pilihan yang tersedia

Sheet or modular conductive tile formatCopper-strip grounding layoutColor-matched hot-welding rodCoved wall transition and conductive adhesive system

Planning a Electrostatic-Conductive PVC Flooring specification?

Kirimkan kami dimensi Anda, kondisi instalasi, target kinerja dan permukaan akhir yang diperlukan.

Bicaralah dengan tim kami