English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أنظمة توزيع الهواء في الغرف النظيفة
غرفة نظيفة تخفيف الضغط المثبط
A finely balanced wall or duct damper that opens above an adjustable pressure differential and closes as the cleanroom returns to its intended cascade.
- Adjustable Differential Setpoint
- Balanced Aerofoil Relief Blade
- Wall or Duct Installation
- Gravity Return Closure
مقدمة المنتج
The cleanroom pressure relief damper uses a low-friction pivoted aerofoil blade and adjustable balance weights to bleed excess air from a positive room. When the differential rises above the selected opening value, blade torque overcomes the balance and the damper opens progressively. As room pressure falls, gravity and the counterweight return the blade toward the sealed position. A wall sleeve, protective grille and accessible weight rail allow the unit to be integrated into clean partitions without exposing the moving mechanism to routine traffic.
الخصائص الرئيسية
Movable weights allow the opening threshold to be adjusted for the intended cleanroom cascade.
Progressive blade travel relieves increasing airflow while avoiding the abrupt full-open action of a simple flap.
Wall, partition and duct configurations accept protective grilles and cleanable powder-coated finishes.
مخاوف المنتج للعملاء
Room-pressure relief must respond at only a few pascals, avoid chatter and close against reverse contamination flow when the positive differential disappears.
Door opening effort rises because the room has no controlled path for excess supply air.The balanced blade opens at the selected differential and releases only the airflow needed to limit overpressure.
A crude gravity flap oscillates as the room controller trims the supply airflow.Aerofoil blade geometry and distributed counterweights provide smoother progressive travel around the setpoint.
Reverse airflow enters when an adjacent room briefly becomes more positive.Gravity return and blade seals close the transfer path as soon as the intended pressure direction is lost.
The counterweight setting is inaccessible after the damper is installed in the wall.A removable clean-side grille exposes the calibrated weight rail without dismantling the sleeve.
تطبيقات نموذجية
Pharmaceutical cleanroom pressure cascadesOperating theatre suitesLaboratory pressure transfer pathsMedical-device clean assemblyAirlocks and gowning rooms
المعلمات الفنية
Typical construction ranges for a wall-mounted cleanroom pressure relief damper are listed below.
| المواد الأساسية | Extruded aluminum aerofoil blade with stainless pivots, elastomer seals and adjustable steel counterweights |
|---|---|
| سمك اللوحة | 20–35 mm hollow aerofoil blade depth |
| العرض الفعال | 300–900 mm nominal free opening width |
| الحد الأقصى الطول | Up to 1275 mm modular frame height |
| الصلب يواجه سمك | 1.0–1.5 mm powder-coated sleeve, grille and counterweight support |
| الكثافة الأساسية | Approximately 2700 kg/m³ for the aluminum relief blade |
| الموصلية الحرارية | Approximately 160–205 W/(m·K) for the aluminum blade section |
| إنهاء السطح | White powder-coated frame and grille with natural or coated aluminum blade |
| نوع المشترك | Through-wall or flanged duct sleeve with pivoted balanced blade, perimeter seal and removable grille |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Factory opening range from 15 to 75 PaClean-side or service-side weight accessProtective grille or weather louverPowder-coated aluminum or stainless-steel construction
Planning a Cleanroom Pressure Relief Damper specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
