Three-quarter view of a cleanroom pressure relief damper with wall sleeve

Sistem Pengedaran Udara Bilik Bersih

Damper Pelepasan Tekanan Bilik Bersih

A finely balanced wall or duct damper that opens above an adjustable pressure differential and closes as the cleanroom returns to its intended cascade.

Adjustable Differential Setpoint
Balanced Aerofoil Relief Blade
Wall or Duct Installation
Gravity Return Closure

Permintaan sebut harga Semak imbas produk

Pengenalan Produk

The cleanroom pressure relief damper uses a low-friction pivoted aerofoil blade and adjustable balance weights to bleed excess air from a positive room. When the differential rises above the selected opening value, blade torque overcomes the balance and the damper opens progressively. As room pressure falls, gravity and the counterweight return the blade toward the sealed position. A wall sleeve, protective grille and accessible weight rail allow the unit to be integrated into clean partitions without exposing the moving mechanism to routine traffic.

Ciri-ciri Utama

A balanced aerofoil blade responds to small pressure differences without electrical power or tubing.

Movable weights allow the opening threshold to be adjusted for the intended cleanroom cascade.

Progressive blade travel relieves increasing airflow while avoiding the abrupt full-open action of a simple flap.

Wall, partition and duct configurations accept protective grilles and cleanable powder-coated finishes.

Kebimbangan Produk Pelanggan

Room-pressure relief must respond at only a few pascals, avoid chatter and close against reverse contamination flow when the positive differential disappears.

Door opening effort rises because the room has no controlled path for excess supply air.The balanced blade opens at the selected differential and releases only the airflow needed to limit overpressure.

A crude gravity flap oscillates as the room controller trims the supply airflow.Aerofoil blade geometry and distributed counterweights provide smoother progressive travel around the setpoint.

Reverse airflow enters when an adjacent room briefly becomes more positive.Gravity return and blade seals close the transfer path as soon as the intended pressure direction is lost.

The counterweight setting is inaccessible after the damper is installed in the wall.A removable clean-side grille exposes the calibrated weight rail without dismantling the sleeve.

Permohonan yang biasa

Pharmaceutical cleanroom pressure cascadesOperating theatre suitesLaboratory pressure transfer pathsPerhimpunan bersih peranti perubatanAirlocks and gowning rooms

Parameter teknikal

Typical construction ranges for a wall-mounted cleanroom pressure relief damper are listed below.

Bahan Teras	Extruded aluminum aerofoil blade with stainless pivots, elastomer seals and adjustable steel counterweights
Ketebalan Panel	20–35 mm hollow aerofoil blade depth
Lebar berkesan	300–900 mm nominal free opening width
Panjang maksimum	Up to 1275 mm modular frame height
Keluli Menghadapi Ketebalan	1.0–1.5 mm powder-coated sleeve, grille and counterweight support
Ketumpatan teras	Approximately 2700 kg/m³ for the aluminum relief blade
Kekonduksian Terma	Approximately 160–205 W/(m·K) for the aluminum blade section
Kemasan permukaan	White powder-coated frame and grille with natural or coated aluminum blade
Jenis Bersatu	Through-wall or flanged duct sleeve with pivoted balanced blade, perimeter seal and removable grille
Penyesuaian	Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi.

Pilihan yang boleh didapati

Factory opening range from 15 to 75 PaClean-side or service-side weight accessProtective grille or weather louverPowder-coated aluminum or stainless-steel construction

Planning a Cleanroom Pressure Relief Damper specification?

Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.

Berbincang dengan pasukan kami