English
الألمانية
العربيةالحالي
الفرنسية
الإندونيسية
اليابانية
الكورية
اللغة الملاوية
البرتغالية
الروسية
الإسبانية
التايلاندية
اللغة التركية
اللغة الفيتنامية
أبواب الغرف النظيفة ونوافذ وأنظمة التشابك
Aالتلقائي محكم انزلاق الباب
A touchless automatic sliding doorset that lowers and compresses the leaf against full-perimeter seals during final closure to support pressure-critical sterile rooms.
- Final Compression Closing Motion
- Full-Perimeter Hermetic Seal
- Touchless Automatic Access
- Pressure-Stable Sterile Boundary
مقدمة المنتج
The Automatic Hermetic Sliding Door follows a shaped track that moves the leaf horizontally during travel and then draws it inward and downward at the final closing position. This movement compresses the head, jamb and threshold seals around the complete opening. A stainless-faced polyurethane-cored leaf provides a rigid gasket plane, while the monitored operator controls motion, obstruction reversal and hold-open time for beds, carts and personnel.
الخصائص الرئيسية
Touchless activation supports sterile transfer without shared handle contact.
Rigid stainless-faced construction preserves a straight sealing plane over repeated cycles.
Safety monitoring reverses the door if an obstruction is detected during closure.
Programmable speeds and hold-open time accommodate personnel, trolley and bed traffic.
مخاوف المنتج للعملاء
Hermetic sliding doors must compress uniformly after every cycle while remaining safe, touchless and practical for wide clinical or cleanroom traffic.
A conventional sliding leaf passes near the frame but does not compress the seals.The final inward-and-downward motion applies controlled pressure around the complete perimeter.
Floor, jamb and head leakage paths respond differently to ordinary brush seals.Matched compression gaskets close all four sides through one coordinated leaf movement.
A heavy sealed leaf can create a safety risk during powered closure.Position monitoring and obstruction detection command immediate reversal and low-speed recovery.
Slow sealed doors delay clinical beds and large cleanroom carts.Adjustable travel and hold-open settings match the clear opening to the expected traffic type.
تطبيقات نموذجية
Operating theatresSterile pharmaceutical suitesIsolation and intensive-care roomsHigh-grade cleanroom airlocksPressure-controlled biomedical laboratories
المعلمات الفنية
Representative physical dimensions for an automatic hermetic sliding doorset are listed below.
| المواد الأساسية | Closed-cell rigid polyurethane foam with internal reinforcement |
|---|---|
| سمك اللوحة | 40-50 mm hermetic sliding leaf |
| العرض الفعال | 800-2500 mm clear opening |
| الحد الأقصى الطول | 2400 mm standard leaf height |
| الصلب يواجه سمك | 0.8-1.0 mm 304 stainless or powder-coated steel skins |
| الكثافة الأساسية | 40-45 kg/m³ polyurethane |
| الموصلية الحرارية | 0.022-0.028 W/(m·K) typical polyurethane core range |
| إنهاء السطح | Brushed 304 stainless steel or smooth powder-coated steel |
| نوع المشترك | Shaped overhead track with final inward/downward leaf compression against four-side gaskets |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
Touchless hand, foot or radar activationBattery backup and manual releaseFlush double-glazed vision panelInterlock and access-control integration
Planning a Automatic Hermetic Sliding Door specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
