Rectangular opposed blade volume control damper with external linkage

Temiz Oda Hava Dağıtım Sistemleri

Blade Volume Control Damper (Blade Volume Kontrol Damper)

A rectangular multiblade damper whose adjacent linked blades rotate in opposite directions for stable duct volume control and compact shutoff.

True Opposed Blade Action
External Linkage
Low-Leakage Edge Seals
Manual or Motorized Drive

Alıntı isteği Browse ürünleri

Ürün tanıtımı

The opposed blade volume control damper regulates air through rectangular cleanroom branches, equipment inlets and wall openings. Alternating aerofoil blades rotate toward and away from each other through an external linkage, dividing the throttling effect across the full face rather than concentrating it at one edge. A rigid channel frame keeps blade shafts aligned, while tip and side seals reduce closed-position leakage. The drive remains outside the airstream and can accept a manual quadrant, electric actuator or pneumatic operator.

Ana Özellikler

Alternating blade rotation creates a more even downstream velocity profile during throttled operation.

External linkage keeps moving joints out of the primary air path and visible for inspection.

Formed aerofoil blades resist vibration and reduce pressure loss when fully open.

Side and blade-tip seals limit bypass when the damper is used for branch isolation.

Müşteri Ürün Sorunları

A balancing damper must provide stable modulation without blade chatter, distorted downstream flow or excessive closed-position leakage.

Parallel blades push most throttled airflow toward one side of the downstream duct.Opposed blade motion divides the openings across the face and produces a more balanced discharge profile.

Large blades twist or chatter under high duct velocity.Double-skin aerofoil sections and intermediate shaft supports maintain blade rigidity across wider dampers.

Internal linkage cannot be inspected without opening contaminated ductwork.The drive arm, transverse link and blade connectors are mounted outside the casing.

Air continues leaking through a nominally closed branch.Compressible blade-tip and side seals close the remaining gaps between aerofoil blades and frame.

Tipik uygulamalar

Cleanroom branch duct balancingAir-handler inlet and discharge controlSupply and extract isolationPlenum pressure adjustmentProcess exhaust volume regulation

Teknik parametreler

Representative material and dimensional ranges for a rectangular opposed blade control damper are listed below.

Temel malzemeler	Galvanized-steel or 304 stainless-steel channel frame with linked double-skin aerofoil blades
Panel kalınlığı	1.0–2.0 mm frame channels and double-skin blade sheets
Effective Width (Etkili Genişlik)	200–2000 mm nominal single-section width
Maksimum uzunluk	Up to 2000 mm single-section width, with subdivided assemblies for larger openings
Çelik yüz yüze kalınlığı	1.0–2.0 mm galvanized or stainless frame and blade material
Core Density (Çekirdek Yoğunluğu)	Approximately 7850 kg/m³ for galvanized-steel frame and blade construction
Termal İletkenlik	Approximately 45–60 W/(m·K) for galvanized-steel frame and blade construction
Yüzey bitirme	Mill-galvanized, white powder-coated or brushed stainless-steel finish
Ortak tip	Flanged rectangular frame with external opposed-action linkage and sealed blade edges
Customization (Özelleşme)	Kullanılan uygulama ve çalışma ortamına göre kullanılabilir.

Mevcut Seçenekler

Galvanized steel or 304 stainless steelManual quadrant, electric actuator or pneumatic driveLow-leakage blade and jamb sealsFlanged, drilled or corner-hole duct frame

Planning a Opposed Blade Volume Control Damper specification?

Bize boyutlarınızı, montaj koşullarınızı, performans hedeflerinizi ve gerekli yüzey kaplamalarınızı gönderin.

Ekibimizle konuşun